UMLIFE 20A Brushed ESC Instruction Manual

ആമുഖം

Thank you for choosing the UMLIFE 20A Brushed Electronic Speed Controller (ESC). This manual provides essential information for the safe and efficient operation of your ESC. This device is designed for use with various RC models, including cars, boats, and tanks, offering precise motor control with forward, reverse, and brake capabilities.

സുരക്ഷാ വിവരങ്ങൾ

• Always disconnect the battery from the ESC when not in use to prevent accidental operation and potential damage.
• Ensure all connections are secure and correctly polarized before applying power. Incorrect wiring can damage the ESC, motor, or battery.
• Operate RC models in open areas, away from people, animals, and obstacles.
• നിർദ്ദിഷ്ട വോളിയം കവിയരുത്tage and current ratings. Overloading can lead to overheating and permanent damage.
• Keep the ESC away from water and moisture unless specifically designed for waterproof operation.
• 14 വയസ്സിന് താഴെയുള്ള ഉപയോക്താക്കൾക്ക് മുതിർന്നവരുടെ മേൽനോട്ടം ശുപാർശ ചെയ്യുന്നു.

ഉൽപ്പന്ന സവിശേഷതകൾ

• നിലവിലെ റേറ്റിംഗ്: Constant 20A, Maximum 25A (<30s), Pulsed 50A (<5s).
• ഓപ്പറേറ്റിംഗ് വോളിയംtage: 4.8V - 8.4V (compatible with 2S LiPo batteries).
• ഡ്രൈവ് ഫ്രീക്വൻസി: 2kHz
• മോട്ടോർ അനുയോജ്യത: Supports 130, 180, 260, 280, and 380 brushed motors.
• പ്രവർത്തനങ്ങൾ: Forward, Reverse, and Brake.
• BEC put ട്ട്‌പുട്ട്: 5.7V, 1A (for receiver/servo power).
• കോംപാക്റ്റ് ഡിസൈൻ: Lightweight and suitable for various mini RC applications.

പാക്കേജ് ഉള്ളടക്കം

• 4 x UMLIFE 20A Brushed ESC Units

Setup and Wiring

Proper wiring is crucial for the correct function and longevity of your ESC. Refer to the diagram below for connection points.

ചിത്രം: Wiring diagram for the 20A Brushed ESC. This image illustrates the connection points for the signal line (to receiver), battery interface (power input), motor interface (power output to motor), and the physical switch for power on/off. It also highlights the "With/without brake switch" setting on the ESC board.

1. റിസീവറുമായി ബന്ധിപ്പിക്കുക: Plug the signal line (black, red, white wires) from the ESC into the throttle channel of your RC receiver. The white wire is typically signal, red is positive (BEC output), and black is negative.
2. ബാറ്ററിയുമായി ബന്ധിപ്പിക്കുക: Connect your battery pack to the battery interface (red and black wires with a connector, typically JST or similar). Ensure correct polarity: red to positive (+), black to negative (-). The ESC supports 2S LiPo or 4-7 cell Ni-MH/Ni-Cd batteries (4.8V-8.4V). Do not use 3S LiPo batteries as this can damage the ESC.
3. Connect to Motor: Connect your brushed motor to the motor interface (red and black wires). The polarity here determines the motor's rotation direction. If the motor spins in the wrong direction, reverse the motor wires. The ESC is compatible with 130, 180, 260, 280, and 380 brushed motors.
4. Brake Switch Setting: The ESC features a small switch on the board to enable or disable the brake function. Adjust this switch according to your preference for braking behavior. Refer to the image for the location of this switch.
5. വൈദ്യുതി സ്വിച്ച്: Use the external power switch to turn the ESC on or off.

പ്രവർത്തന നിർദ്ദേശങ്ങൾ

Once all connections are made and verified:

1. Turn on your RC transmitter first.
2. Then, turn on the power switch on the ESC.
3. The ESC will initialize. Wait for any calibration tones or LED indicators to confirm it's ready.
4. Use the throttle stick on your transmitter to control the motor.
   • ഫോർവേഡ്: Push the throttle stick forward.
   • വിപരീതം: Pull the throttle stick backward from the neutral position.
   • ബ്രേക്ക്: If the brake function is enabled via the onboard switch, moving the throttle stick to neutral after a forward or reverse input will engage the brake.
5. After operation, turn off the ESC power switch first, then turn off your transmitter.

മെയിൻ്റനൻസ്

• Keep the ESC clean and free from dust, dirt, and debris.
• Regularly inspect all wires and connectors for signs of wear or damage. Replace any damaged components immediately.
• ഉപയോഗത്തിലില്ലാത്തപ്പോൾ, ESC വരണ്ടതും തണുത്തതുമായ അന്തരീക്ഷത്തിൽ സൂക്ഷിക്കുക.
• Avoid exposing the ESC to extreme temperatures or direct sunlight for prolonged periods.

ട്രബിൾഷൂട്ടിംഗ്

• Motor not responding:
  • Check all wiring connections (battery, motor, receiver signal).
  • Ensure the battery is charged and connected with correct polarity.
  • Verify the transmitter is on and properly bound to the receiver.
  • Confirm the motor is compatible with the ESC (brushed type, within current limits).
• Motor spins in wrong direction:
  • Reverse the two motor wires connected to the ESC.
• No brake function:
  • Check the position of the onboard brake switch. Ensure it is set to the "with brake" position.
  • Verify your transmitter's throttle trim and sub-trim settings are centered.
• ESC or motor overheating:
  • Ensure the motor is not undersized for the application or experiencing excessive load.
  • Check for any binding in the drivetrain that could cause extra strain.
  • ബാറ്ററി വോളിയം സ്ഥിരീകരിക്കുകtage is within the specified range (4.8V-8.4V). Using higher voltage (e.g., 3S LiPo) will damage the ESC.

സ്പെസിഫിക്കേഷനുകൾ

വാറൻ്റിയും പിന്തുണയും

വാറന്റി വിവരങ്ങൾ, സാങ്കേതിക പിന്തുണ, അല്ലെങ്കിൽ സേവന അന്വേഷണങ്ങൾ എന്നിവയ്ക്ക്, ദയവായി നിർമ്മാതാവിനെയോ നിങ്ങളുടെ വാങ്ങൽ കേന്ദ്രത്തെയോ ബന്ധപ്പെടുക. വാങ്ങിയതിന്റെ തെളിവായി നിങ്ങളുടെ വാങ്ങൽ രസീത് സൂക്ഷിക്കുക.