Annovi Reverberi Foam Lance User Manual

ഉൽപ്പന്നം കഴിഞ്ഞുview

The Annovi Reverberi Foam Lance is designed for efficient car washing, transforming your pressure washer into a powerful foam cleaning system. This 750 ml foam cleaner is compatible with various Annovi Reverberi cold water pressure washer models.

പ്രധാന സവിശേഷതകൾ:

• Specifically designed for Annovi Reverberi AR Blue Clean pressure washers.
• Connects via a bayonet fitting directly to the high-pressure gun.
• Compatible with 1-series (AR116, AR117, AR142, AR143), 3-series (AR371, AR375, AR386, AR396, AR399), and 4-series (AR471, AR473, AR475, AR476, AR162K-XTRA, AR181K-XTRA) models.

Image: The Annovi Reverberi Foam Lance, showing the clear reservoir filled with blue cleaning solution, and the black nozzle assembly with a grey adjustment knob. The reservoir has volume markings up to 750ml.

സജ്ജീകരണ നിർദ്ദേശങ്ങൾ

Follow these steps to properly set up your Annovi Reverberi Foam Lance:

1. പരിഹാരം തയ്യാറാക്കുക: Fill the 750 ml reservoir with your desired car wash soap and water mixture. Refer to your soap's instructions for the correct dilution ratio.
2. Detach End Lance: If your pressure washer's high-pressure gun has an existing end lance attached, detach it according to your pressure washer's manual.
3. Connect Foam Lance: Insert the bayonet fitting of the foam lance directly onto the high-pressure gun of your compatible Annovi Reverberi pressure washer. Ensure it clicks securely into place.
4. അനുയോജ്യത പരിശോധിക്കുക: This foam lance is compatible with the following AR Blue Clean pressure washer series:
   • 1-series: AR116, AR117, AR142, AR143
   • 3-series: AR371, AR375, AR386, AR396, AR399
   • 4-series: AR471, AR473, AR475, AR476, AR162K-XTRA, AR181K-XTRA

Image: The Annovi Reverberi Foam Lance, showing the clear reservoir with a prominent "750 ML" marking, indicating its capacity. The nozzle assembly is black with a grey adjustment knob.

പ്രവർത്തന നിർദ്ദേശങ്ങൾ

Once the foam lance is securely attached and filled with solution, you can begin operation:

1. പ്രഷർ വാഷർ ആരംഭിക്കുക: Turn on your pressure washer according to its operating manual.
2. Adjust Foam Output: The grey knob on top of the foam lance allows you to adjust the foam thickness and spray pattern. Turn it clockwise for thicker foam and a narrower spray, and counter-clockwise for thinner foam and a wider spray.
3. നുരയെ പുരട്ടുക: Aim the foam lance at the surface you wish to clean. Squeeze the trigger on your pressure washer gun to dispense foam. Apply an even layer of foam over the entire surface.
4. താമസിക്കാനുള്ള സമയം അനുവദിക്കുക: Let the foam dwell on the surface for a few minutes to break down dirt and grime. Do not let the foam dry on the surface.
5. കഴുകുക: After the dwell time, remove the foam lance and reattach your standard pressure washer lance (or use a rinse nozzle if available) to rinse off the foam and loosened dirt thoroughly.

മെയിൻ്റനൻസ്

Proper maintenance ensures the longevity and optimal performance of your foam lance:

• ഉപയോഗത്തിന് ശേഷം കഴുകിക്കളയുക: After each use, empty any remaining soap solution from the reservoir. Fill the reservoir with clean water and run it through the foam lance for a few minutes to flush out any soap residue. This prevents clogging and corrosion.
• വൃത്തിയുള്ള നോസൽ: Periodically check the nozzle for any blockages. If necessary, clean it with a small brush or needle.
• ശരിയായി സംഭരിക്കുക: Store the foam lance in a clean, dry place, away from direct sunlight and extreme temperatures. Ensure the reservoir is empty and dry before storage.
• കണക്ഷനുകൾ പരിശോധിക്കുക: Regularly inspect the bayonet connection and other parts for wear or damage. Replace any worn or damaged components immediately.

ട്രബിൾഷൂട്ടിംഗ്

If you encounter issues with your foam lance, try these solutions:

• No Foam or Weak Foam:
  • Ensure the soap solution is mixed correctly and the reservoir is not empty.
  • Check if the foam adjustment knob is set correctly.
  • Verify that the pressure washer is operating at its correct pressure.
  • Inspect the nozzle for blockages and clean if necessary.
• Leaks from Connections:
  • Ensure the foam lance is securely attached to the pressure washer gun.
  • Check for damaged O-rings or seals and replace them if worn.
• Inconsistent Spray Pattern:
  • ഏതെങ്കിലും അവശിഷ്ടങ്ങൾ നീക്കം ചെയ്യാൻ നോസൽ വൃത്തിയാക്കുക.
  • Ensure the foam adjustment knob is not loose or damaged.

പ്രശ്നങ്ങൾ നിലനിൽക്കുകയാണെങ്കിൽ, ഉപഭോക്തൃ പിന്തുണയുമായി ബന്ധപ്പെടുക.

സാങ്കേതിക സവിശേഷതകൾ

വാറൻ്റിയും പിന്തുണയും

For specific warranty information regarding your Annovi Reverberi Foam Lance, please refer to the documentation provided with your purchase or contact the seller directly. Warranty terms may vary by region and retailer.

For technical support, product inquiries, or assistance with troubleshooting beyond this manual, please visit the official Annovi Reverberi website or contact their customer service department. Keep your product model number (46343) and purchase details ready when seeking support.