1. ആമുഖം
This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your EUROMAIR EOLE T2 + HV230-30950 paint sprayer system. Please read this manual thoroughly before initial use and keep it for future reference.
The EUROMAIR EOLE T2 is a compact, portable turbine system designed for various painting applications, including lacquers, varnishes, and primers, suitable for both water-based and solvent-based products. Its lightweight and user-friendly design make it ideal for small to medium-sized projects.
2 സുരക്ഷാ വിവരങ്ങൾ
Always observe the following safety precautions to prevent personal injury and damage to the equipment:
- ഉപകരണം പ്രവർത്തിപ്പിക്കുന്നതിന് മുമ്പ് എല്ലാ നിർദ്ദേശങ്ങളും വായിക്കുക.
- Wear appropriate personal protective equipment (PPE), including eye protection, gloves, and a respirator, especially when spraying paints and solvents.
- അപകടകരമായ പുക അടിഞ്ഞുകൂടുന്നത് തടയാൻ ജോലിസ്ഥലത്ത് മതിയായ വായുസഞ്ചാരം ഉറപ്പാക്കുക.
- Do not operate the sprayer near open flames, pilot lights, or other ignition sources.
- Always disconnect the power supply before cleaning, servicing, or performing maintenance on the unit.
- കുട്ടികളെയും വളർത്തുമൃഗങ്ങളെയും ജോലിസ്ഥലത്ത് നിന്ന് അകറ്റി നിർത്തുക.
- Use only genuine EUROMAIR replacement parts and accessories.
- ഉപകരണങ്ങൾ ഒരു തരത്തിലും പരിഷ്കരിക്കരുത്.
3. ഉൽപ്പന്നം കഴിഞ്ഞുview ഘടകങ്ങളും
The EUROMAIR EOLE T2 + HV230-30950 system includes the following main components:
Figure 1: Complete EUROMAIR EOLE T2 + HV230-30950 Paint Sprayer System. This image shows the compact turbine unit in red and black, with a black handle, connected to a silver HVLP spray gun with red accents. The system is designed for portability and ease of use.
- Turbine Unit: The main power unit that generates compressed air.
- HVLP Spray Gun (HV230): Equipped with a 1.5 mm nozzle for precise application.
- എയർ ഹോസ്: 4-meter hose with quick-release ball fittings for connecting the turbine to the spray gun.
- Viscometer: Tool for measuring paint viscosity.
- ക്ലീനിംഗ് ബ്രഷ്: For maintenance of the spray gun and components.
- Nozzle Cleaning Needle: For clearing blockages in the spray gun nozzle.
- Multi-service Wrench: For assembly and disassembly of components.
4. സജ്ജീകരണ നിർദ്ദേശങ്ങൾ
- ഘടകങ്ങൾ അൺപാക്ക് ചെയ്യുക: Carefully remove all items from the packaging and verify that all listed components are present.
- Position the Turbine: Place the turbine unit on a stable, level surface in a well-ventilated area, away from any potential ignition sources.
- എയർ ഹോസ് ബന്ധിപ്പിക്കുക: Attach one end of the 4-meter air hose to the air outlet on the turbine unit and the other end to the air inlet on the HVLP spray gun. Ensure quick-release fittings are securely engaged.
- Prepare Spray Gun:
- Ensure the 1.5 mm nozzle is correctly installed on the spray gun.
- Attach the 1-liter paint cup (godet) to the bottom of the spray gun.
- പവർ കണക്ഷൻ: Plug the turbine unit's power cord into a grounded 230 V / 10 A / 50-60 Hz electrical outlet.
5. പ്രവർത്തന നിർദ്ദേശങ്ങൾ
5.1. Preparing the Material
- Consult the paint manufacturer's instructions for thinning recommendations.
- Use the provided viscometer to check the viscosity of the paint. The paint should flow smoothly through the viscometer within the recommended time frame for spraying.
- Filter the paint through a fine mesh strainer to remove any impurities that could clog the nozzle.
- Pour the prepared paint into the 1-liter cup of the spray gun.
5.2. Adjusting the Spray Gun
The HVLP spray gun features adjustable controls for optimal application:
- Product Flow Adjustment: Use the knob at the rear of the gun to control the amount of paint released. Turn clockwise to decrease flow, counter-clockwise to increase.
- സ്പ്രേ പാറ്റേൺ ക്രമീകരണം: Rotate the air cap at the front of the gun to change the spray pattern from horizontal to vertical or a round pattern.
5.3. Spraying Technique
- Turn on the turbine unit.
- Hold the spray gun perpendicular to the surface, approximately 15-25 cm (6-10 inches) away.
- Move the gun in smooth, even passes, overlapping each pass by about 50%.
- Release the trigger at the end of each pass to avoid paint buildup.
- Apply multiple thin coats rather than one thick coat for a better finish and to prevent runs.
6. പരിപാലനം
6.1. Cleaning After Use
Proper cleaning is crucial for the longevity and performance of your sprayer:
- Empty Paint Cup: Remove any remaining paint from the cup.
- Rinse Cup: Fill the cup with the appropriate cleaning solution (water for water-based paints, solvent for solvent-based paints) and spray it through the gun until clear.
- Disassemble Gun: Disassemble the air cap, nozzle, and fluid needle. Clean all parts thoroughly with the cleaning brush and solution.
- Clean Air Passages: Ensure no paint has entered the air passages.
- വീണ്ടും കൂട്ടിച്ചേർക്കുക: Reassemble the spray gun, ensuring all parts are dry and correctly fitted.
6.2. Turbine Maintenance
- Regularly check the air filter on the turbine unit and clean or replace it as needed to maintain optimal airflow and prevent overheating.
- Keep the exterior of the turbine unit clean and free of dust and debris.
6.3. സംഭരണം
Store the unit in a clean, dry place, away from extreme temperatures and direct sunlight. Ensure the spray gun is thoroughly cleaned before storage.
7. പ്രശ്നപരിഹാരം
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| സ്പ്രേ ഇല്ല അല്ലെങ്കിൽ ദുർബലമായ സ്പ്രേ | Clogged nozzle; insufficient material; air leak; turbine filter clogged. | Clean nozzle with needle; refill paint cup; check hose connections; clean/replace turbine filter. |
| അസമമായ സ്പ്രേ പാറ്റേൺ | Dirty air cap; incorrect spray pattern adjustment; paint too thick. | Clean air cap; adjust air cap position; thin paint to recommended viscosity. |
| പെയിന്റ് ഒടിഞ്ഞുപോകുകയോ തൂങ്ങുകയോ ചെയ്യുന്നു | Too much paint applied; gun too close to surface; paint too thin. | Reduce product flow; increase distance from surface; thicken paint or apply thinner coats. |
| Turbine not starting | No power; faulty switch. | Check power connection and outlet; contact customer support if switch is faulty. |
8 സാങ്കേതിക സവിശേഷതകൾ
Turbine Unit
- Stages: 2
- സമ്മർദ്ദം: 0.3 ബാർ
- ക്രമീകരിക്കാവുന്ന വായുപ്രവാഹം: ഇല്ല
- ശക്തി: 1100 W
- വൈദ്യുതി വിതരണം: 230 V / 10 A / 50 & 60 Hz
- ഹോസ് നീളം: 4 മീ
- അളവുകൾ (L x W x H): 27 x 20 x 36 സെ.മീ
- ഭാരം: 7 കി.ഗ്രാം
- ശബ്ദ നില: 91 Lwa
HVLP സ്പ്രേ ഗൺ
- Product Flow Adjustment: അതെ
- സ്പ്രേ പാറ്റേൺ ക്രമീകരണം: അതെ
- വായു മർദ്ദം ക്രമീകരിക്കൽ: ഇല്ല
- കപ്പ് ശേഷി: 1 എൽ
- അളവുകൾ (L x W x H): 18 x 11 x 29 സെ.മീ
- ഭാരം: 0.83 കി.ഗ്രാം
9. വാറൻ്റിയും പിന്തുണയും
For warranty information, please refer to the documentation provided with your purchase or contact EUROMAIR customer service. Keep your proof of purchase for warranty claims.
For technical support, spare parts, or service inquiries, please contact your authorized EUROMAIR dealer or visit the official EUROMAIR website. Ensure you have your model number (E11830950) and serial number ready when contacting support.
