1. ആമുഖം
The FLIPSKY 75200 Pro V2.0 is an advanced electronic speed controller (ESC) designed for high-performance electric vehicles such as skateboards, scooters, and ebikes. It features an aluminum PCB for enhanced heat dissipation and an integrated power button for convenient operation. This manual provides essential information for setup, operation, and maintenance of your FLIPSKY 75200 Pro V2.0 ESC.
Figure 1: FLIPSKY 75200 Pro V2.0 Electronic Speed Controller.
2. ഉൽപ്പന്ന സവിശേഷതകൾ
- ഫേംവെയർ: Version 6.02, with support for future firmware updates.
- വാല്യംtagഇ ശ്രേണി: 14-84V (4-20S battery configurations).
- നിലവിലെ ശേഷി: 100A continuous, with burst capabilities (values depend on mounting, ambient temperature, and air circulation).
- BEC: 5V@1.5A output.
- Motor Control Modes: Supports BLDC square wave mode and FOC sine wave mode.
- ERPM: 150,000 വരെ.
- ആശയവിനിമയ ഇന്റർഫേസുകൾ: USB, CAN, UART.
- പിന്തുണയ്ക്കുന്ന സെൻസറുകൾ: ABI, HALL, AS5047, AS5048A.
- Input Set Support: PPM, ADC, NRF, UART.
- വയർ വലിപ്പം: 10AWG for main power wires.
- പ്രോഗ്രാമബിൾ: Yes, via VESC_TOOL.
- പുനരുൽപ്പാദന ശേഷി: അതെ.
- Phase Filter: Included for stable operation.
- പവർ സ്വിച്ച് ബട്ടൺ: Integrated red power switch button.
- Integrated Bluetooth Module: Allows convenient connection to Bluetooth parameters and real-time data reading without external modules.
- Advanced Protections: കുറഞ്ഞ വോളിയം ഉൾപ്പെടുന്നുtagഇ, ഉയർന്ന വോള്യംtage, over current, temperature, MOSFET, and motor over-temperature protection.
- നിയന്ത്രണ മോഡുകൾ: Supports Current / Duty cycle / Speed / PID control modes.
- IMU Module Support: Compatible with IMU modules like MPU9250, MPU6050, LSM6DS3, BMI160 via IIC interface for balancing car functions.
- സിപിയു: 32F405 with 168MHz frequency.
- താപ വിസർജ്ജനം: Aluminum PCB and aluminum case design provide good heat dissipation for extended lifespan.
3 സ്പെസിഫിക്കേഷനുകൾ
| സ്പെസിഫിക്കേഷൻ | മൂല്യം |
|---|---|
| ഫേംവെയർ | 6.02 (firmware update supported) |
| വാല്യംtagഇ റേഞ്ച് | 14-84 വി (4-20 എസ്) |
| തുടർച്ചയായ കറൻ്റ് | 100എ |
| BEC ഔട്ട്പുട്ട് | 5V@1.5A |
| ERPM | 150,000 |
| Control Interface Ports | USB, CAN, UART |
| പിന്തുണയ്ക്കുന്ന സെൻസറുകൾ | ABI, HALL, AS5047, AS5048A |
| Input Set Support | PPM, ADC, NRF, UART |
| വയർ വലിപ്പം | 10AWG |
| അളവുകൾ (L x W x H) | 130mm x 67.7mm x 39.4mm |
| മെറ്റീരിയൽ | അലുമിനിയം |
| നിറം | കറുപ്പ് |
ചിത്രം 2: ഉൽപ്പന്ന അളവുകൾ.
Figure 3: Internal PCB dimensions.
4. സജ്ജീകരണം
Proper connection of the FLIPSKY 75200 Pro V2.0 is crucial for safe and optimal performance. Refer to the diagram below for connection points.
ചിത്രം 4: കണക്ഷൻ ഡയഗ്രം.
4.1. പവർ കണക്ഷനുകൾ
- ബാറ്ററി: Connect your battery pack to the main red (+) and black (-) terminals. Ensure correct polarity. The ESC supports 4-20S battery configurations.
- മോട്ടോർ: Connect the three phase wires (blue, green, yellow) from your motor to the corresponding terminals on the ESC.
- വൈദ്യുതി സ്വിച്ച്: Connect the integrated power switch to the designated port.
4.2. Sensor and Communication Connections
- ഹാൾ സെൻസർ: If your motor has Hall sensors, connect the Hall sensor cable to the HALL port on the ESC. Ensure the pinout matches.
- PPM (Pulse Position Modulation): For throttle input from a remote receiver, connect the PPM signal wire to the PPM port.
- CAN (Controller Area Network): Use the CAN bus for communication between multiple ESCs (e.g., in a dual motor setup) or other CAN-enabled devices.
- USB: Connect the ESC to a computer via the USB port for configuration and firmware updates using the VESC_TOOL software.
- UART (Universal Asynchronous Receiver-Transmitter): For serial communication with external modules like Bluetooth modules (though this ESC has integrated Bluetooth) or other accessories.
- COMM: This port provides additional communication lines for various sensors or peripherals.
4.3. Initial Configuration (VESC_TOOL)
After physical connections, the ESC requires configuration using the VESC_TOOL software. This software allows you to set motor parameters, battery limits, control modes, and perform motor detection. It is highly recommended to follow the official VESC_TOOL documentation for detailed configuration steps to prevent damage to the ESC or motor.
- Download the latest VESC_TOOL from the official VESC project webസൈറ്റ്.
- Connect the ESC to your computer via USB.
- Launch VESC_TOOL and perform motor detection.
- Configure battery voltage limits, current limits, and other safety parameters according to your setup.
- Utilize the integrated Bluetooth module to connect to the VESC_TOOL mobile application for real-time data monitoring and parameter adjustments.
Video 1: Demonstration of the 75200 Pro V2.0 ESC features and operation.
5. പ്രവർത്തന നിർദ്ദേശങ്ങൾ
Once properly configured, the FLIPSKY 75200 Pro V2.0 ESC is ready for operation. The ESC supports various control modes to suit different applications and user preferences.
5.1. പവർ ഓൺ/ഓഫ്
- Press the integrated red power button to turn the ESC on or off.
- പവർ ഓണാക്കുന്നതിന് മുമ്പ് എല്ലാ കണക്ഷനുകളും സുരക്ഷിതമാണെന്ന് ഉറപ്പാക്കുക.
5.2. നിയന്ത്രണ മോഡുകൾ
The ESC can be configured for the following control modes via VESC_TOOL:
- നിലവിലെ നിയന്ത്രണം: Motor current is directly controlled by the input signal.
- Duty Cycle Control: മോട്ടോർ വോളിയംtage is controlled as a percentage of the battery voltage.
- Speed Control (RPM): The ESC attempts to maintain a target motor RPM.
- PID നിയന്ത്രണം: Advanced control loop for precise speed or position control, often used with IMU modules for balancing applications.
5.3. Regenerative Braking
The ESC supports regenerative braking, which converts kinetic energy back into electrical energy to recharge the battery during braking. Ensure that regenerative current limits are set appropriately in VESC_TOOL to avoid overcharging your battery.
Video 2: Short demonstration of the FLIPSKY 75100/75200 series ESC.
6. പരിപാലനം
Regular maintenance helps ensure the longevity and reliable performance of your FLIPSKY 75200 Pro V2.0 ESC.
- വൃത്തിയായി സൂക്ഷിക്കു: Periodically clean the exterior of the ESC to prevent dust and debris buildup, especially on the heatsink fins. Use a soft, dry cloth.
- കണക്ഷനുകൾ പരിശോധിക്കുക: Regularly inspect all wire connections (battery, motor, sensors, communication) for looseness, corrosion, or damage. Secure any loose connections.
- താപനില നിരീക്ഷണം: While the ESC has built-in temperature protection, it is good practice to monitor its temperature during heavy use, especially in enclosed spaces. Ensure adequate airflow around the unit.
- ഫേംവെയർ അപ്ഡേറ്റുകൾ: Check for official firmware updates periodically using VESC_TOOL. Updates can provide performance improvements, bug fixes, and new features.
- സംഭരണം: When not in use for extended periods, store the ESC in a dry, cool environment away from direct sunlight and extreme temperatures.
ചിത്രം 5: താഴെ view highlighting the heatsink for good heat dissipation.
7. പ്രശ്നപരിഹാരം
If you encounter issues with your FLIPSKY 75200 Pro V2.0 ESC, consider the following troubleshooting steps:
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| ESC പവർ ഓൺ ചെയ്യുന്നില്ല. | Loose battery connection, faulty power button, dead battery. | ബാറ്ററി വോളിയം പരിശോധിക്കുകtage and connections. Ensure the power button is correctly connected and functioning. |
| Motor not spinning or erratic behavior. | Incorrect motor phase wire connection, incorrect Hall sensor connection, improper VESC_TOOL configuration. | Verify motor and Hall sensor wiring. Re-run motor detection in VESC_TOOL. Check motor and battery current limits. |
| ESC overheating. | Insufficient airflow, excessive current draw, incorrect motor parameters. | Ensure proper ventilation. Reduce load or adjust current limits in VESC_TOOL. Check motor resistance and inductance values. |
| ബ്ലൂടൂത്ത് കണക്ഷൻ പ്രശ്നങ്ങൾ. | Interference, incorrect pairing procedure, outdated VESC_TOOL app. | Ensure no strong interference sources. Follow the pairing instructions for the VESC_TOOL app. Update the app to the latest version. |
For more detailed diagnostics and advanced troubleshooting, refer to the comprehensive documentation available for VESC-based ESCs and the FLIPSKY support resources.
വീഡിയോ 3: കഴിഞ്ഞുview of the VESC 75200 Pro.
8. വാറൻ്റിയും പിന്തുണയും
8.1. വാറൻ്റി വിവരങ്ങൾ
The FLIPSKY 75200 Pro V2.0 ESC comes with a 2 മാസ വാറൻ്റി വാങ്ങിയ തീയതി മുതൽ. സാധാരണ ഉപയോഗ സാഹചര്യങ്ങളിൽ നിർമ്മാണ വൈകല്യങ്ങൾ ഈ വാറന്റി ഉൾക്കൊള്ളുന്നു. വാറന്റി ക്ലെയിമുകൾക്കായി നിങ്ങളുടെ വാങ്ങിയതിന്റെ തെളിവ് സൂക്ഷിക്കുക.
8.2. ഉപഭോക്തൃ പിന്തുണ
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact FLIPSKY customer support through their official website or the retailer from whom you purchased the product. Provide your product model, serial number (if applicable), and a detailed description of the issue to expedite support.
