1. ആമുഖം
This manual provides essential information for the safe and effective operation of your FLIPSKY 75100 Pro V2.0 Speed Controller. Please read this manual thoroughly before installation and use to ensure optimal performance and longevity of the device.
The FLIPSKY 75100 Pro V2.0 is an advanced Electronic Speed Controller (ESC) designed for electric skateboards, scooters, and e-bikes. It features an aluminum PCB for enhanced heat dissipation and supports various control modes and sensor types.
2 സുരക്ഷാ വിവരങ്ങൾ
- Always disconnect power before performing any installation, maintenance, or wiring changes.
- Ensure all connections are secure and correctly polarized to prevent damage to the ESC or other components.
- Operate the ESC within its specified voltage and current limits to avoid overheating and component failure.
- വെള്ളം, ഈർപ്പം, കടുത്ത താപനില എന്നിവയിൽ നിന്ന് ESC അകറ്റി നിർത്തുക.
- Installation should be performed by individuals with adequate knowledge of electronics and electrical systems.
- Regularly inspect wiring and connections for signs of wear or damage.
3. ഉൽപ്പന്ന സവിശേഷതകൾ
The FLIPSKY 75100 Pro V2.0 ESC incorporates several key features for robust and flexible performance:
- Firmware: 6.02 (firmware update supported)
- Adjustable protection against: low voltagഇ, ഉയർന്ന വോള്യംtage, over current, temperature abnormal, MOSFETs/motor over temperature.
- Support for BLDC square wave mode control and FOC sine wave mode.
- Aluminum PCB for enhanced heat dissipation and extended lifespan.
- Programmable functionality.
- Regenerative braking capacity.
- Integrated power switch button (Red).
Figure 1: FLIPSKY 75100 Pro V2.0 Speed Controller with various connection wires and power button.
4. സജ്ജീകരണവും കണക്ഷനുകളും
Proper connection of the ESC is critical for its functionality and safety. Refer to the connection diagram below for guidance.
Figure 2: Connection diagram illustrating battery, motor, and control signal ports.
4.1. പവർ കണക്ഷനുകൾ
- ബാറ്ററി: Connect your battery pack to the main power input wires (red for positive, black for negative). Ensure correct polarity. The ESC supports 14-84V (4-20S) input.
- മോട്ടോർ: Connect the three motor phase wires to the corresponding output wires from the ESC. The wires are typically black and do not require specific phase matching; the ESC will handle it.
- വൈദ്യുതി സ്വിച്ച്: Connect the red power switch button to its designated port.
4.2. Control and Sensor Connections
- HALL Sensors: Connect the motor's HALL sensor wires to the HALL port on the ESC. Supported sensors include ABI, HALL, AS5047, AS5048A.
- PPM/PWM: For throttle input, connect your receiver's PPM/PWM signal to the PPM port.
- CAN ബസ്: Use the CAN port for communication between multiple ESCs (master/slave configuration) or other CAN-enabled devices.
- UART: The UART port allows for communication with external modules like Bluetooth modules or other microcontrollers.
- USB: Connect the ESC to a computer via the USB port for configuration and firmware updates using VESC Tool software.
- ADC-കൾ: Analog-to-Digital Converter ports are available for various analog inputs.
പ്രധാനപ്പെട്ടത്: When unplugging connectors, press the release tab to avoid damaging wires or the connector itself.
5. പ്രവർത്തന നിർദ്ദേശങ്ങൾ
After successful installation and configuration using the VESC Tool, the ESC is ready for operation.
- പവർ ഓൺ: Press the red power switch button to turn on the ESC. The LED indicator will illuminate.
- ത്രോട്ടിൽ നിയന്ത്രണം: Apply throttle input via your connected PPM/PWM device. The ESC will control the motor speed and direction based on your input and configured settings.
- ബ്രേക്കിംഗ്: The ESC supports regenerative braking. Applying reverse throttle will engage braking, which also recharges the battery to some extent.
- നിരീക്ഷണം: Use the VESC Tool connected via USB or UART (e.g., Bluetooth module) to monitor real-time parameters such as motor RPM, current, voltagഇ, താപനില.
- പവർ ഓഫ്: Press and hold the red power switch button to turn off the ESC.
6. പരിപാലനം
- പതിവ് പരിശോധന: Periodically check all wiring and connectors for signs of wear, corrosion, or loose connections.
- വൃത്തിയാക്കൽ: Keep the ESC clean and free from dust, dirt, and debris. Use a soft, dry brush or compressed air. Avoid using liquids.
- ചൂട് മാനേജ്മെൻ്റ്: Ensure adequate airflow around the ESC, especially during high-power operation, to utilize its aluminum PCB's heat dissipation capabilities effectively.
- ഫേംവെയർ അപ്ഡേറ്റുകൾ: Check for and apply firmware updates periodically using the VESC Tool to benefit from performance improvements and bug fixes.
7. പ്രശ്നപരിഹാരം
| പ്രശ്നം | സാധ്യമായ കാരണം | പരിഹാരം |
|---|---|---|
| ESC പവർ ഓൺ ചെയ്യുന്നില്ല. | No power from battery, faulty power switch, incorrect wiring. | ബാറ്ററി വോളിയം പരിശോധിക്കുകtage, inspect power switch connection, verify main power wiring. |
| Motor not spinning or erratic behavior. | Incorrect motor detection, loose motor phase wires, sensor issues, incorrect VESC Tool configuration. | Perform motor detection in VESC Tool, check motor wire connections, inspect sensor wiring, review VESC Tool settings. |
| ESC overheating. | Excessive load, insufficient cooling, short circuit, incorrect current limits. | Reduce load, ensure adequate airflow, check for shorts, adjust current limits in VESC Tool. |
| ത്രോട്ടിൽ പ്രതികരണമില്ല. | PPM/PWM signal not connected, incorrect receiver settings, VESC Tool input configuration error. | Verify PPM/PWM connection, check receiver output, configure input in VESC Tool. |
8 സ്പെസിഫിക്കേഷനുകൾ
| ഫീച്ചർ | വിശദാംശങ്ങൾ |
|---|---|
| ഫേംവെയർ | 6.02 (firmware update supported) |
| അളവുകൾ (L*W*H) | 103 മിമി * 58 മിമി * 27.7 മിമി |
| വാല്യംtagഇ റേഞ്ച് | 14-84 വി (4-20 എസ്) |
| തുടർച്ചയായ കറൻ്റ് | 100എ |
| BEC ഔട്ട്പുട്ട് | 5V@1.5A |
| നിയന്ത്രണ മോഡുകൾ | BLDC square wave, FOC sine wave |
| Max ERPM | 150000 |
| Control Interface Ports | USB, CAN, UART |
| പിന്തുണയ്ക്കുന്ന സെൻസറുകൾ | ABI, HALL, AS5047, AS5048A |
| Input Set Support | PPM, ADC, NRF, UART |
| വയർ വലിപ്പം | 10AWG (75100 Pro) |
| പ്രോഗ്രാമബിൾ | അതെ |
| Regenerative Capacity | അതെ |
| ഘട്ടം ഫിൽട്ടർ | അതെ |
| പവർ സ്വിച്ച് ബട്ടൺ | ചുവപ്പ് |
| മെറ്റീരിയൽ | അലുമിനിയം |
| ഇനത്തിൻ്റെ ഭാരം | 0.3 കിലോഗ്രാം |
Figure 3: Dimensions of the FLIPSKY 75100 Pro V2.0 Speed Controller.
9. വാറൻ്റിയും പിന്തുണയും
9.1. വാറൻ്റി വിവരങ്ങൾ
The FLIPSKY 75100 Pro V2.0 Speed Controller comes with a warranty of 2 months or more, as specified by the manufacturer. Please retain your proof of purchase for warranty claims. The warranty covers manufacturing defects under normal use conditions. Damage resulting from improper installation, misuse, modification, or exceeding specified limits may void the warranty.
9.2. സാങ്കേതിക പിന്തുണ
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact FLIPSKY customer support through their official website or the retailer from whom the product was purchased. Ensure you have your product model number and purchase details ready.
10. അധിക ഉൽപ്പന്നം Views
ചിത്രം 4: മറ്റൊന്ന് view of the FLIPSKY 75100 Pro V2.0 with connected wires.
ചിത്രം 5: മുകളിൽ view of the FLIPSKY 75100 Pro V2.0, highlighting the ports and branding.
ചിത്രം 6: വശം view of the FLIPSKY 75100 Pro V2.0, showcasing the ribbed aluminum casinതാപ വിസർജ്ജനത്തിന് ഗ്രാം.
ചിത്രം 7: കോണാകൃതിയിലുള്ളത് view of the FLIPSKY 75100 Pro V2.0.
ചിത്രം 8: മുൻഭാഗം view of the FLIPSKY 75100 Pro V2.0.
ചിത്രം 9: ആന്തരിക view of the FLIPSKY 75100 Pro V2.0 circuit board, showing components and capacitors.
No official product videos from the seller were found to be relevant for embedding in this manual.
