VTSYIQI പോർട്ടബിൾ അൾട്രാസോണിക് ഫ്ലാവ് ഡിറ്റക്ടർ യൂസർ മാനുവൽ

1. ആമുഖം

The VTSYIQI Portable Ultrasonic Flaw Detector is an advanced digital instrument designed for non-destructive testing. It enables quick, easy, and accurate detection, localization, evaluation, and diagnosis of various internal defects in workpieces, such as cracks, welds, pores, sand holes, and inclusions. This device is widely used in industries including electric power, petrochemical, boiler and pressure vessel manufacturing, steel structure fabrication, military, aerospace, railway transportation, and automotive sectors.

2. പാക്കേജ് ഉള്ളടക്കം

Verify that all items listed below are present and in good condition upon unpacking:

• Main Body (Ultrasonic Flaw Detector Unit)
• Straight Beam Probe
• Angle Probe
• Machine-probe Cable
• പവർ അഡാപ്റ്റർ (ചാർജർ)
• Data Processing Software
• യുഎസ്ബി കമ്മ്യൂണിക്കേഷൻ കേബിൾ
• ഇൻസ്ട്രക്ഷൻ മാനുവൽ
• ഉപകരണ കേസ്
• പായ്ക്കിംഗ് ലിസ്റ്റ്

Figure 2.1: The complete package contents, including the main unit, probes, cables, power adapter, and carrying case.

3. ഉൽപ്പന്നം കഴിഞ്ഞുview

The VTSYIQI Portable Ultrasonic Flaw Detector features a robust design with an intuitive interface for efficient operation. Key components include the main display, control panel, probe connectors, and USB communication ports.

ചിത്രം 3.1: മുൻഭാഗം view of the VTSYIQI Portable Ultrasonic Flaw Detector with its integrated stand, showing the display and control buttons.

ചിത്രം 3.2: വശം view highlighting the USB communication ports for data transfer to a PC.

ചിത്രം 3.3: പിൻഭാഗം view of the device, showing the battery compartment and product label.

4. സജ്ജീകരണം

4.1 ബാറ്ററി ചാർജ് ചെയ്യുന്നു

The device uses a lithium battery. Before initial use, or if the instrument has not been used for a long time, it must be charged. Charge the battery at least once a month to prevent over-discharging.

1. Connect the power adapter to the charging port on the device.
2. അനുയോജ്യമായ ഒരു ഇലക്ട്രിക്കൽ ഔട്ട്ലെറ്റിലേക്ക് പവർ അഡാപ്റ്റർ പ്ലഗ് ചെയ്യുക.
3. The "Charging" indicator light on the control panel will illuminate.
4. Allow the device to charge until the indicator light changes or turns off, indicating a full charge.

4.2 കണക്ടിംഗ് പ്രോബുകൾ

Proper connection of the ultrasonic probe is crucial for accurate measurements.

1. Identify the appropriate probe (straight beam or angle probe) for your inspection task.
2. Connect one end of the machine-probe cable to the probe.
3. Connect the other end of the machine-probe cable to the corresponding port on the top of the flaw detector unit. Ensure a secure connection.

Figure 4.1: The flaw detector connected to an angle probe, ready for material inspection.

5. ഓപ്പറേഷൻ

5.1 പവർ ഓൺ/ഓഫ്

• പവർ ഓണാക്കാൻ, അമർത്തിപ്പിടിക്കുക പവർ ഡിസ്പ്ലേ പ്രകാശിക്കുന്നത് വരെ ബട്ടൺ അമർത്തുക.
• പവർ ഓഫ് ചെയ്യുന്നതിന്, അമർത്തിപ്പിടിക്കുക പവർ button until the display shuts down.

5.2 Basic Measurement Modes

The device supports various measurement display modes:

• Positive Wave: Displays the positive half of the ultrasonic signal.
• Negative Wave: Displays the negative half of the ultrasonic signal.
• Full Wave: Displays both positive and negative halves of the signal.
• തരംഗം: General waveform display.

Use the control panel buttons to navigate and select the desired mode.

5.3 Probe Calibration (Angle Probe Exampലെ)

Accurate calibration is essential for reliable flaw detection. This example demonstrates angle probe calibration.

1. Connect the angle probe to the device.
2. Place the angle probe on a known calibration block.
3. അമർത്തുക ഓട്ടോ കലോറി ബട്ടൺ.
4. എന്നിട്ട് അമർത്തുക F2 to initiate calibration.
5. Adjust the probe position to find the highest echo on the display.
6. അമർത്തുക പ്രവേശിക്കുക key to calibrate the P Delay and angle.
7. Observe the K value on the display for verification.

5.4 വിപുലമായ സവിശേഷതകൾ

• Linear Suppression: Maximum inhibition of 80% of screen height.
• Probe Switching: Easily switch between single crystal and double crystal probes.
• Gate Setting & Alarm: Set gate position and width, configure incoming wave alarms.
• DAC Curve: Automatic generation with up to 10 recordable points and four adjustable offset curves.
• AVG Curve: Automatic generation with customization for two defect types.
• Automatic Probe Calibration: Streamlined calibration process.
• ഡാറ്റ സംഭരണം: Store 100 A-sweep patterns, parameters, and DAC curves.
• Storage Graphics Playback: View stored A-scan graphics.
• Peak Memory Function: Capture and recall peak values.
• Freeze and Thaw Functions: For waveform and inspection parameters.
• Sound Path Measurement & Echo Frequency Analysis: Advanced analysis capabilities.
• യുഎസ്ബി ആശയവിനിമയം: Connect to PC for data transfer and processing.

Figure 5.1: The flaw detector in use for various applications, including steel plate, casting, forging, and weld inspections.

6. പരിപാലനം

• വൃത്തിയാക്കൽ: Regularly clean the device and probes with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
• സംഭരണം: Store the instrument in its protective case in a dry, cool environment when not in use.
• ബാറ്ററി കെയർ: As mentioned in Section 4.1, charge the lithium battery at least once a month to maintain its lifespan, even if not in active use.
• പ്രോബ് കെയർ: Ensure probes are clean and free from damage. Inspect cables for wear and tear before each use.

7. പ്രശ്‌നപരിഹാരം

8 സ്പെസിഫിക്കേഷനുകൾ

9. വാറൻ്റിയും പിന്തുണയും

For warranty information, technical support, or service inquiries, please refer to the documentation included with your product or contact VTSYIQI customer service through their official channels. Keep your purchase receipt as proof of purchase for warranty claims.

നിർമ്മാതാവ്: VTSYIQI20240827145632VTSYIQI