1. ആമുഖം
The Matek Mateksys AP_PERIPH CAN-L4-BM is an ultra-precise digital power monitor designed for applications requiring accurate current and voltage measurements via the CAN bus. It utilizes the TI INA239 IC and runs ArduPilot AP_Periph firmware, supporting the CAN/DroneCAN protocol. This device provides reliable power monitoring without the need for calibration.
2. സവിശേഷതകൾ
- Ultra-precise digital power monitoring.
- Based on TI INA239 and ArduPilot AP_Periph firmware.
- Supports CAN/DroneCAN protocol.
- No calibration required for accurate current and bus voltage readouts.
- Low power loss due to 200µΩ typical conductive path resistance.
3 സ്പെസിഫിക്കേഷനുകൾ
- MCU: STM32L431xC, 256KB Flash
- Power Monitor IC: INA239 (85-V, 16-Bit, High-Precision)
- ബാറ്ററി വോളിയംtage Sense Input: 0~85V
- Current Sense Range: 0~204.8എ
- Load Current on Sensing Resistor: 150A (Continuous), 204.8A (Burst)
- വാല്യംtagഇ കൃത്യത: 0.1%
- നിലവിലെ കൃത്യത: 2%
- ഇൻ്റർഫേസ്: CAN (DroneCAN Protocol), UART2 (spare, DFU), ST debug (SWCLK & SWDIO)
- വൈദ്യുതി വിതരണം: 4.5~5.5V @5V pad/pin
- വൈദ്യുതി ഉപഭോഗം: 10mA
- പ്രവർത്തന താപനില: -40~85 °C
- ബോർഡ് വലിപ്പം: 30mm x 22mm x 3mm
- ഭാരം: 4g
- ഫേംവെയർ: ArduPilot AP_Periph (Update via DroneCAN GUI Tool)
4. ഉൽപ്പന്നം കഴിഞ്ഞുview
ഘടക ലേഔട്ട്
5. സജ്ജീകരണവും ഇൻസ്റ്റാളേഷനും
വയറിംഗ് നിർദ്ദേശങ്ങൾ
Proper wiring is crucial for accurate readings and safe operation of the CAN-L4-BM.
General Wiring Tips
- Solder the positive wires as close as possible to both sides of the current sensing resistor on the board for optimal accuracy.
- Ensure a common ground connection between the flight controller and the ESC/Load to prevent ground loops and ensure stable operation.
- If CAN wires are excessively long, bridge the 120R jumper on the CAN-L4-BM board to maintain signal integrity.
- The large pad on the bottom side of the board is a dead pad and has no circuit network; it can be used for structural support if needed.
- The two mounting ears can be carefully cut off if not required for installation in space-constrained environments.
ഫേംവെയർ കോൺഫിഗറേഷൻ
The CAN-L4-BM runs ArduPilot AP_Periph firmware. Configuration is performed via the DroneCAN protocol through your flight controller's settings.
- Connect the CAN-L4-BM to your flight controller's CAN bus port.
- Set the appropriate parameter in your flight controller's firmware to enable the CAN driver:
- For CAN bus1:
CAN_P1_DRIVER = 1 - For CAN bus2:
CAN_P2_DRIVER = 1
- For CAN bus1:
- Configure battery monitoring by setting:
BATTx_MONITOR = 8(DroneCAN-BatteryInfo), where 'x' corresponds to the battery monitor instance you are configuring. - Firmware updates for the CAN-L4-BM can be performed using the DroneCAN GUI Tool.
6. ഓപ്പറേഷൻ
LED സൂചകങ്ങൾ
- Blue LED (Fast blinking): Indicates the board is in the process of booting up.
- Blue LED (Slow blinking): Indicates the board is working correctly and communicating via CAN.
- ചുവന്ന LED: Indicates that 3.3V power is present on the board.
ഡാറ്റ മോണിറ്ററിംഗ്
Once properly configured and powered, the flight controller will receive accurate current and bus voltage data from the CAN-L4-BM via the DroneCAN bus. This data can be logged and monitored through your flight controller's telemetry system or compatible ground station software.
7. പരിപാലനവും മികച്ച രീതികളും
- Regularly inspect all soldered connections for integrity and signs of wear or corrosion.
- Keep the board free from dust, moisture, and debris to ensure optimal performance and longevity.
- Ensure proper ventilation if operating the device in enclosed spaces, although the CAN-L4-BM has a wide operating temperature range.
- Avoid exposing the board to extreme environmental conditions (e.g., excessive humidity, direct water contact) beyond its specified operating range.
8. പ്രശ്നപരിഹാരം
പൊതുവായ പ്രശ്നങ്ങൾ
- No data from monitor:
- Verify all CAN bus connections (CAN-H, CAN-L, GND, 5V) are secure and correct.
- Check the LED indicators for proper boot and operation (a slow blue blink indicates normal function).
- ഉറപ്പാക്കുക
CAN_P1_DRIVERorCAN_P2_DRIVERis set correctly in the flight controller parameters. - അത് സ്ഥിരീകരിക്കുക
BATTx_MONITOR = 8is set for the correct battery monitor instance. - Check for any short circuits or incorrect voltage supply to the CAN-L4-BM board.
- കൃത്യമല്ലാത്ത വായനകൾ:
- Ensure positive wires are soldered as close as possible to the current sensing resistor on the board.
- Verify common ground connections between all components in the power system.
- Check for any physical damage to the board or its components that might affect sensor accuracy.
- Board not powering on:
- Confirm that a stable 4.5~5.5V supply is provided to the 5V pad/pin.
- Check the Red 3.3V indicator LED; if it's off, there might be a power issue.
- Inspect all power supply wiring for breaks or incorrect connections.
9. ബന്ധപ്പെടലും പിന്തുണയും
For further assistance, technical support, or to access additional resources, please refer to the official Mateksys documentation available on their website or consult relevant community forums for ArduPilot and DroneCAN users.
