GOTEL SL200 Lamination Machine
സുരക്ഷാ നിർദ്ദേശങ്ങൾ
- The product must be used by its intended use
- Keep away from children and animals. This product is not a toy.
- This device is not intended for use by persons (including children) with reduced physical, sensory or mental abilities or lack of experience or knowledge. They should be supervised and instructed in the use of the device by a person responsible for their safety.
- Do not place fingers, hair, loose clothing or jewelry near the paper feed slot as this may cause serious injury.
- The laminator will be very hot during use, so be careful when handling the device.
- ലാമിനേറ്റ് ചെയ്യുന്നതിന് മുമ്പ് പേപ്പർ ക്ലിപ്പുകളും സ്റ്റേപ്പിളുകളും നീക്കം ചെയ്യുക.
- Laminate only paper or cardboard. Do not laminate unusual items.
- Use the device on a flat and stable surface.
- Make sure there is enough free space at the back of the device for the lamination to exit the device.
- SL200 works with laminating pouches from 160 (2×80) microns to 250 (2×125) microns thick (credit card size to A4 size)
- Do not use aerosols or cleaning agents.
- Do not spray or lubricate the machine.
- ലാമിനേറ്ററിൽ പ്ലഗ് ഇൻ ചെയ്യുന്നതിനുമുമ്പ് ഓൺ/ഓഫ് സ്വിച്ച് ഓഫ് പൊസിഷനിൽ ആണെന്ന് ഉറപ്പാക്കുക.
- ഉൽപ്പന്നത്തിൽ അടയാളപ്പെടുത്തിയിരിക്കുന്ന എല്ലാ മുന്നറിയിപ്പുകളും നിർദ്ദേശങ്ങളും പാലിക്കുക.
- ലാമിനേറ്റർ ഉപയോഗത്തിലില്ലാത്തപ്പോഴോ നീക്കുന്നതിനോ വൃത്തിയാക്കുന്നതിനോ മുമ്പോ അൺപ്ലഗ് ചെയ്യുക.
- Clean the laminator only with a dry cloth.
- Do not place the machine near a heat source or in a damp പരിസ്ഥിതി.
- If the power cord is damaged, it must be replaced by a qualified electrician to avoid a hazard.
- The items to be laminated must not be metal or plastic (iron, copper, aluminum, etc.).
- Do not insert anything into the machine except laminating pouches and the suggested items. The machine is intended for laminating only.
- Never remove the cover or disassemble the machine, there are no serviceable parts inside.
- Do not use this product in a humid or hot environment.
- പവർ സപ്ലൈയുമായി ബന്ധിപ്പിക്കുന്നതിന് മുമ്പ്, വോളിയം പരിശോധിക്കുകtage of the local power source corresponds to the voltage indicated on this device.
- Do not use damaged power cords or plugs to operate this product. If the product malfunctions or is damaged, do not use it. If the power cord or this product is damaged, return it to an authorized after-sales service center.
- When the device requires cleaning, disconnect the power plug.
- പവർ കോർഡ് അല്ലെങ്കിൽ പ്ലഗ് കേടായാൽ ഉപയോഗിക്കരുത്.
- Do not use a damaged electrical installation.
- Do not bend, stretch or entangle the power cord. Do not press the power cord with heavy objects, risk of damage to the product.
- Do not disconnect the power cord or touch the device with wet or damp hands, risk of electric shock.
- Do not modify the device without authorisation.
- Make sure the power socket is installed correctly and that the plug does not get hot.
Operating the laminator:
- SL200 is operated by a rocker switch, located at the right-hand side of the appliance.
- Plug the machine’s cable into a convenient 13 Amp domestic supply outlet.
- For COLD laminating, select the COLD setting, the Green ready light will come on straight away and COLD laminating can begin, (please note you will need special Cold Laminating Pouches).
- For HOT laminating, select the Hot setting. Hot laminating can begin when the Green “Ready” light comes on (Allow approx 2-4 minutes heat up time).
- If choosing COLD laminating after you have been Hot Laminating the machine must be allowed to cool to room temperature again 4. Prepare the laminating pouch for inserting into the machine. See How to load a laminating pouch below Do not use pouches thicker than 250mic (2x125mic per side)
- When the machine has reached operating temperature, you may insert the pouch (sealed edge first) squarely into the machine until it engages with the rollers. Never insert a pouch open edge first into the machine.
- പൗച്ച് മെഷീനിലൂടെ നീങ്ങുകയും പിന്നിൽ നിന്ന് പുറത്തുകടക്കുകയും ചെയ്യും.
- During the process the READY light may go out as heat is absorbed by the laminating pouch. This is normal.
- Turn the laminator to OFF (O) after use.
- വൈദ്യുതി വിതരണത്തിൽ നിന്ന് പ്ലഗ് നീക്കം ചെയ്യുക.
- The minimum laminating thickness is 160 (2×80) microns and the maximum thickness is 250 (2×125) microns..
- IMPORTANT! Do not touch the top of the machine during use, as this gets very hot. The intermittent operation on this machine is 30mins On and 10 minutes Off, but we recommend that you allow the machine to cool down for at least
- 15mins after 30mins use. Do not place items on top of the machine at any time.
- How to load a laminating pouch:
- The laminating pouch is sealed along one side.
- Open the pouch and place the paper to be laminated centrally inside the pouch as close to the sealed edge as possible. Ensure there is an equal border all round the paper (eg: A4 paper should have a 3mm border).
- The sealed edge (not the open edges) is placed into the entry slot to start the lamination process.
സ്പെസിഫിക്കേഷനുകൾ
Rollers: 2 Roller (hot shoe)
- Entry width: 230mm
- Min pouch thickness: 160(2×80) micron
- Max pouch thickness: 250 (2×125) micron
- Min pouch size: Credit card size (54x86mm)
- Max pouch size: A4 size
- Max lamination thickness: 0.5mm Laminating speed: 280 mm/min Warm-up: 2-3minutes
- വൈദ്യുതി ഉപഭോഗം: 260W
- Input: AC220-240V / 50Hz Dimensions: 352X126X75mm
- ABS – a system that prevents jamming or excessive film tension
- Hot/Off/Cold – laminator operating mode:
- Hot – hot laminating mode
- Cold – cold laminating mode
- Off – device turned off
ഇറക്കുമതിക്കാരൻ
GOTEL Sp. z o.o Porosły-Kolonia 4B 16-070 Choroszcz kontakt@gotel.com.pl
ചൈനയിൽ നിർമ്മിച്ചത്
പതിവായി ചോദിക്കുന്ന ചോദ്യങ്ങൾ
Q: What is the maximum lamination thickness supported by the SL200 laminator?
A: The maximum lamination thickness supported by the SL200 laminator is 0.5mm.
Q: How do I prevent jamming or excessive film tension during lamination?
A: The SL200 laminator features an ABS system that prevents jamming or excessive film tension. Ensure to follow the recommended pouch thickness and operating procedures to avoid issues.
പ്രമാണങ്ങൾ / വിഭവങ്ങൾ
 |
GOTEL SL200 Lamination Machine [pdf] നിർദ്ദേശങ്ങൾ SL200 Lamination Machine, SL200, Lamination Machine, Machine |