HILAND 0909 Sensor

സ്പെസിഫിക്കേഷനുകൾ

• Model: KMix 0909
• Connectivity: MicroUSB to USB, M XLR, M TRS, M TS, M Banana
• Power Requirements: Phantom Power +48V
• Sampലിംഗ് നിരക്ക്: 96000

ഉൽപ്പന്ന ഉപയോഗ നിർദ്ദേശങ്ങൾ

Cables Needed: 

• Micro-USB to USB Cable.
• Power Jumper Cable for 0909:
• M XLR to M TRS x2 and M TRS to M TRS x6:
• M 1/8 TRS to LEFT/RIGHT M TS M TS (Y Cable):
• M XLR to +/- M Banana x2 (Y CABLE):

Phantom Power Test

1. Enter the serial number in the box at the top of the program.
2. Plug the USB end of the Micro USB cable into the computer. Plus Micro USB end of the Micro USB cable into the Audio port of the KMix 0909 board. Plug the power jumper cable into 4 pin and 8-pin ports on the KMix 0909 board.
3. M XLR to +/- M Banana. Plug the M XLR into Input 1 and 2 of the 0909 Board.
4. Plug + (Red) Banana into mAVΩ port and plug – (Black) Banana into COM port. Set the multimeter mode to measure DC Voltage. Turn on the Multimeter.
5. Toggle Phantom Power ON by clicking and holding the Phantom button.
6. വോളിയം പരിശോധിക്കുകtage of Phantom Power on the Multimeter. Phantom Power voltage should be roughly +48V.
7. വോളിയം നൽകുകtages into fields
8. Release Phantom Power button to turn Phantom Power OFF. Move on to Sensor Test.

സെൻസർ ടെസ്റ്റ്

1. Input 1 to Output 1. Input 2 to Output 2. Input 3 to Output 3. Input 4 to Output 4. Input 5 to Output 5. Input 6 to Output 6. Input 7 to Output 7. Input 8 to Output 8.
2. Open Sensor Test.
3. Click the Audio Status Button to access the audio status window.
4. Set to Input and Output to KMix. Set Sampling Rate to 96000.
5. The power symbol will turn grey when changes are made. Click the power symbol to turn Audio back on. The power symbol will turn blue.
6. Double-click the Assign Port button (ctlout). Set Control Out Port to “KMix Audio Control In”.
7. Start Test (Step 2, Phase 1).
8. Y Cable from Headphone Out to Inputs 1 and 2.
9. Start Test (Step 4, Phase 3).
10. In Phase 4, click Save Log to save the log for the current board.
11. Clthe reseteset button in Step 1 to reset the test for the next board.
12. Click the Reset button in Step 1 to reset the test for the next board. Repeat all steps above for each 0909 board.

പതിവായി ചോദിക്കുന്ന ചോദ്യങ്ങൾ

What cables are needed for the Sensor Functionality Test?

You will need a MicroUSB to USB cable, Power Jumper Cable, M XLR to M TRS x2, M TRS to M TRS x6, M 1/8 TRS to LEFT/RIGHT M TS M TS (Y Cable), and M XLR to +/ M Banana x2 (Y Cable).

How do I check Phantom Power voltage?

Toggle Phantom Power ON, measure the voltage using a multimeter. It should read around +48V. Enter the voltages into the designated fields and then turn off Phantom Power.

പ്രമാണങ്ങൾ / വിഭവങ്ങൾ

HILAND 0909 Sensor [pdf] ഉടമയുടെ മാനുവൽ 0909 Sensor, 0909, Sensor

റഫറൻസുകൾ

• ഉപയോക്തൃ മാനുവൽ