LED CTRL FXN സിംഗിൾ കളർ പാനൽ ഇൻസ്റ്റലേഷൻ ഗൈഡ്

 FXN Single Colour Panel
ഇൻസ്റ്റലേഷൻ ഗൈഡ്

ഇൻസ്റ്റലേഷൻ

ഉൽപ്പന്നം

ആക്സസറികളും ടൂളുകളും

Gluing process (if needed)

1. The external terminal was not treated with waterproofing when shipped.
2. Prepare glue, syringes and other materials.
3. Apply glue to fully cover the terminal, and make sure there’s no bubbles or gaps. The glue should not cover the LEDs, resistors and other components;
4. Power on when the glue is completely dry.

ഇൻസ്റ്റലേഷൻ ഘട്ടങ്ങൾ

കുറിപ്പ്:
“+” connect to white-red wire.
The above pictures are only for reference.
ഇൻസ്റ്റാളേഷന് മുമ്പ് ശ്രദ്ധിക്കുക

• Before installation, check that the product parameters are consistent with the requirements (Seeing product specifications or product labels)
• ലോഡ് വോള്യംtage, current, power and power supply should be matched with the product.
• Follow the instructions of wiring diagram (first connect the load and then the power supply) to avoid short circuit.
• Make sure the correct connection of positive and negative poles between products and power supply. Otherwise, the light will not be on.
• Make sure the power cord firmly screwed into the terminal and it should not be pulled out by hands.
• The terminal should have insulation, waterproof and anti-corrosive treatment.

Common Faults and Troubleshoots

മുന്നറിയിപ്പ്

• Do not disassemble or retrofit the light. Do not touch the surface of the light with a sharp object.
• Do not do live-line working during installation, especially for high voltagഇ ഉൽപ്പന്നം.
• Do not use any organic chemicals solvents.
• Use neutral glass adhesive to fix this product and it needs to be dried 4 hours in the open environment after operation.
• Treat the ends and the circuit connection points that are not connected to the main line with insulation, waterproof, and anti-corrosion in the installation.
• Use 18AWG (0-75mm^2 cross-sectional area) or thicker core wire to avoid adverse consequences caused by overheating, if the power cable need to lengthen.
• ഇൻപുട്ട് വോളിയം ഉറപ്പാക്കുകtage meets the requirements and lines are connected correctly before lighting on.
• This product is for signage, and do not use as general lighting.
• Series connection with the max run.
• The length of the power cable between the power supply and the LED strip should not exceed 2 meters. Otherwise, large circuit loss will lead to inconsistent brightness.
• Installation, maintenance and repair should be operated by a qualified technician.

Statements and Recycling
പ്രസ്താവനകൾ:
Repair should be operated by a qualified technician, if the external circuit or main line of this product is damaged.
The parameters given in this manual are typical values and for reference only.
All illustrations and drawings in this manual are for reference.
This product is subject to change without notice.
പുനരുപയോഗം:

• LED lighting products belongs to electronic products, please do recycling treatment according directives.

Instruction of single-sided lightbox

WWW.LEDCTRL.COM
LED CTRL, 1/483 BALMAIN
LILYFIELD, NSW 2040, AUSTRALIA
സ്പെസിഫിക്കേഷനുകൾ മാറ്റത്തിന് വിധേയമാണ്
WITHOUT NOTICE VISIT WWW.LEDCTRLCOM ഏറ്റവും നിലവിലെ സ്പെസിഫിക്കേഷനുകൾക്കായി.
LED CONTROL PTE LTD UEN 201923077G 2025 LEDCTAL ALL RIGHTS RESERVED.