ഉള്ളടക്കം മറയ്ക്കുക
1 PYLONTECH UP5000 ബാറ്ററി ഫേംവെയർ അപ്‌ഗ്രേഡ് ഉപയോക്തൃ ഗൈഡ്
1.1 Section A: Battery Firmware Upgrade
1.2 Section B: Battery Data Acquirement
1.3 Section C. Special settings for US2000C/US3000C/UP5000
2 പ്രമാണങ്ങൾ / വിഭവങ്ങൾ
2.1 റഫറൻസുകൾ

PYLONTECH UP5000 ബാറ്ററി ഫേംവെയർ അപ്‌ഗ്രേഡ് ഉപയോക്തൃ ഗൈഡ്

PYLONTECH ലോഗോ

പൈലോൺ ടെക്നോളജീസ് കോ., ലിമിറ്റഡ്

No. 73. Lane 887. Zu Chongzhi Road, Zhangjang Hi-Tech Park Pudong,
ഷാങ്ഹായ് 201203, ചൈന

Use Batteryview upgrade and acquire system information Pylontech Low Voltagഇ ഉൽപ്പന്നം

This SOP is for Pylontech authorized software engineer and field application engineer to upgrade and acquire system information of Pylontech Powercube product. To avoid misoperation or commands lead to system failure, please contact Pylontech first before using any of the command not listed in this SOP; Otherwise the product will be out of Pylontech warranty scope.

Section A: Battery Firmware Upgrade

1. Connect from Battery RS232/Console port to laptop USB:
R232 cable sample

Section A Figure 1

For US2000/US3000/Phantom-S/UP2500, the RS232 cable type is RJ11 – DB9 – USB:

Section A Figure 2

For Force L1/L2, the RS232 cable type is RJ45 – DB9 – USB:

Section A Figure 3

Please re-wire the PIN OUT on RJ11/RJ45 side as below:

For RJ11 cable:

Section A Figure 4

For RJ45 cable:

Section A Figure 5

Connect to battery Console Port(as below BLUE circle):

Section A Figure 6

2. Open ‘Batteryview.exe”:

Section A Figure 7

3. Connect to Battery:

Section A Figure 8

The Port Name will be automatically recognized once the RS232 cable is well installed or  from the Device Manager; The Baudrate is 115200.

Section A Figure 9

4. If the BatteryView showed values, which means connect successfully:
*Note: Please double-click the ‘Battery Module’ tool bar to receive correct battery information on the bottom right side, then take a Screenshoot as evidence for further  maintenance task.  

Section A Figure 10

5. Please choose the BMS Update :

Section A Figure 11

6. Click Browse to choose the firmware:

Section A Figure 12

For upgrade US2000B/US3000A/Force-L series product:  

Please select the correct .bin file for the upgrade, by any version of Batteryview.

For upgrade US2000C/US3000C/UP5000:

If the 8th and 9th of the product Serial Number is not ‘E2’ or ‘C3’. it can still select the correct .bin file for the upgrade, by any version of Batteryview.

If the 8th and 9th of the product Serial Number is ‘E2’ or ‘C3’, please select the  correct .zip file for the upgrade, and require to use Batteryview V3.0.28 or higher.  

For upgrade US5000:

If the 8th and 9th of the product Serial Number is ‘C5’ , please select the correct .zip file  for the upgrade, and require to use Batteryview V3.0.28 or higher.  

*It`s suggested to always use the .zip file ബാറ്ററിയുംview V3.0.28 for any  US2000C/US3000C/UP5000/US5000 upgrade to avoid wrong upgrade caused PCBA  damage.  

7. And click Program to start:

Section A Figure 13

8. After it showed the Serial Number, which means update finished.
*Please  keep watching the progress bar and ‘Program’ button till 100%;
In different Operation System, it may happens that the upgrade stick during the process and require to click the ‘Program’ again(once the ‘Program’ button becomes highlighting again during the upgrade process). 

Section A Figure 14

Complete and back to the main page:

Section A Figure 15

Section B: Battery Data Acquirement

  1. Back to Batteryview ‘Mainwindow’, choose ‘History Data Window’ under’ Window(M)’ menu.
    Section B Figure 1
  2. Select data then click the the green down arrow just on the right side
    Section B Figure 2
    Wait for about 1 2mins to let BatteryView acquire the entire cycle data. Then click the save button as below:
    Section B Figure 3p
  3. Save the cycle data to corresponding folder for record.
    Section B Figure 4
  4. For event data acquirement, just select ‘Event data’ as below, then repeat the remainsteps from step 5 to step 6. It`s more critical to save the event data in case a failure.
    Section B Figure 5
    Section B Figure 5 continued
    Please remember to save the Event data to your computer as well as Cycle data.

Section C. Special settings for US2000C/US3000C/UP5000

Below settings only need to be set after swap the PCB of US2000C/US3000C/UP5000.  Settings only available from Batteryview V3.0.22

  1. Connect to battery console port
  2. Choose-options-coul write and mosfail set dialog
    Section C Figure 1
    • Type in number
      If US2000C: 50
      If US3000C: 74
      If UP5000: 100
    • എഴുതുക ക്ലിക്ക് ചെയ്യുക
    • Click Set Mosfail test
      Section C Figure 2
  3. Choose-options-control panel
    Section C Figure 3
    Set Index number0: this will set BMS time same as your PC
    Set Index number 2: this will need to type in the SN on label.

Any further questions to this SOP please contact us via service@pylontech.com.cn.

PYLONTECH ലോഗോ

പൈലോൺ ടെക്നോളജീസ് കോ., ലിമിറ്റഡ്

No. 73. Lane 887. Zu Chongzhi Road, Zhangjang Hi-Tech Park Pudong,
ഷാങ്ഹായ് 201203, ചൈന

പ്രമാണങ്ങൾ / വിഭവങ്ങൾ

PYLONTECH UP5000 Battery Firmware Upgrade [pdf] ഉപയോക്തൃ ഗൈഡ്
UP5000, US5000, US2000B, US3000A, Force-L series, US2000C, US3000C, UP5000 Battery Firmware Upgrade, UP5000, Battery Firmware Upgrade, Firmware Upgrade

റഫറൻസുകൾ

ഒരു അഭിപ്രായം ഇടൂ

നിങ്ങളുടെ ഇമെയിൽ വിലാസം പ്രസിദ്ധീകരിക്കില്ല. ആവശ്യമായ ഫീൽഡുകൾ അടയാളപ്പെടുത്തി *