VPInstruments VM-EN-2500 എനർജി മോണിറ്ററിംഗ് സിസ്റ്റം യൂസർ മാനുവൽ

മുന്നറിയിപ്പ് - ആദ്യം ഇത് വായിക്കുക

	Read and understand user manuals of all equipment involved before commencing installation or use.
	Compressed air can be dangerous! സമ്മർദപൂരിതമായ സാഹചര്യങ്ങളിലുള്ള ശക്തികളെ ദയവായി പരിചയപ്പെടുക. സമ്മർദ്ദമുള്ള ഉപകരണങ്ങളുമായി പ്രവർത്തിക്കുന്നതിനുള്ള പ്രാദേശിക മാർഗ്ഗനിർദ്ദേശങ്ങളും നിയന്ത്രണങ്ങളും മാനിക്കുക.
	All electrical installations to be carried out by authorized electrical installation engineers only.
	മുന്നറിയിപ്പ്: 100…250 VAC mains cables are present in the housing. Do not touch the cables and the power supply when mains is applied. Keep the housing closed during normal operation. Check the cable glands on water tightness.
	Do not overestimate the results. VPInstruments does not take any responsibility for the correctness of measurement results under field conditions. The practical measurement uncertainty of a flow meter in the field may vary, depending on how well it is installed, due to the nature of gas flow. The piping table provides guidelines on how to optimize the field accuracy. Our products are not intended to be used as a single means to determine compressor capacity.
	ചൂട് ഒഴിവാക്കുക. Make sure that the ambient temperature does not exceed the limits. Overheating might cause temporary shutdown or permanent failure of the hardware.
	ഉപകരണം തുറക്കരുത്. Our instruments are assembled with high precision. Opening this device is dangerous and may destroy the instrument. Warranty is voided when you open the instrument.
	Feedback leads to product improvement. Please share your experience with us, as we are continuously improving our products in our commitment to quality, reliability and ease of use. Let us know via sales@vpinstruments.com!

ആമുഖം

അഭിനന്ദനങ്ങൾ! You purchased the easiest to use and fastest compressed air measurement tool in the world. With the VPVision Mobile, you can monitor all your energy utilities simultaneously in the field.

VPVision Mobile offers an all in one solution for audits by using the VPVision M hardware combined with multiple connectivity options in a mobile package. VPVision is a web based energy monitoring system, primarily developed to monitor all energy flows in a plant. It monitors your entire compressed air system from supply to demand side. Thanks to the standardized hardware and the modular software architecture, VPVision is scalable and adaptable.

ഈ മാനുവലിനെക്കുറിച്ച്
We have written this manual to help you to get the VPVision Mobile system up and running in no time. Basic IT and network knowledge is required combined with a basic understanding of flow measurement principles and hardware installation.

സെൻസറുകൾ
VPVision Mobile supports all VPinstruments sensors, and other Modbus RTU or 4..20 mA based sensor types. For some Modbus sensors, we offer pre installed drivers for quick and easy installation. If the pre installed Modbus sensor driver is not available, please contact VPinstruments.

Software options:
VPVision has several software options. See our website for details, as VPVision is continously evolving.

ഭാഷാ ഓപ്ഷനുകൾ:
VPVision is available in intemational English only.
Check the packaging box for any inconsistencies. Should there be any shipping damage, notify the local carrier. At the same time a report should be submitted to Van Putten Instruments BV, Marlotlaan 1G, 2614 GV DELFT, The Netherlands.

For technical questions or support inquiries, please contact us by email at
support@vpinstruments.com.

Older software features may not be covered by the contents of this user manual. Please contact us for a subscription program, which includes software updates!

ഉൽപ്പന്നം കഴിഞ്ഞുview

VPVision Mobile Case
The VPVision Mobile case is the Platform which houses the VPVision Software and offers a wide variety of connectivity options. The case is designed to offer all the functionality of a permanent monitoring system in a portable package. A typical setup for the VPVision Mobile case is to connect it with Multiple sensors (Power/Dew point/Mass Flow) via Modbus TCP, Modbus RS485 or use the 4..20 mA analog inputs with M12 connectors. Next to the standard connectors for measurement the VPVision Mobile case offers the option to connect and extemal wireless antenna or a secondary battery.

1. ഇഥർനെറ്റ്
2. Modbus RS485 (Green = OK, Red = Modbus or power error, Green blinking = communicating)
3. പവർ ഇൻ: Neutrik NAC3MPX-TOP, 90-263VAC
   47-63Hz
4. 8x 4..20mA analog inputs
5. External antenna connection: VPRouter
6. External battery connection: TE
   Connectivity T4130012021-000, 24V
   

9 ഘട്ടങ്ങളിൽ വേഗത്തിൽ ആരംഭിക്കുക

ഘട്ടം 1. Unpack the VPVision Mobile
Unpack the box and check if all items are there and in good shape.

Step 2. Install the VPVision Mobile case
Find a suitable location to install the VPVision Mobile case, preferably flat and dry, away from large machines and crowded paths. Connect the unit to a power source (110-250 VAC).

Step 3. Configure your Modbus devices
Every Modbus device needs configuration. Depending on your type of device, different settings are required. Assign a unique Modbus address to each individual sensor, so they can be found within the Modbus network.
Third party Modbus devices can be added upon request and by consultant of VPInstruments.

Step 4. Install the sensors
Ask your certified (electrical) installation subcontractor to install the sensors, and connect it to the Modbus network. Install analog sensors and make a list of analog input channels on your configuration sheet. See also the documentation example.

Step 5. Configure inputs
Configure the input channels in the backend of VPVision. You can add the sensors via the web ഇൻ്റർഫേസ്. Use your configuration sheet as a reference for the channel names, sensor locations, sensor ranges, diameter settings, etc.

Step 6. Configure widgets
Once the channels are in place, you can start to configure the widgets. Several types are available to visualize all the data.
Widgets and sections can be named in a preferred language.

Step 7. Configure pages
Once the channels and widgets are in place, you can start to configure the pages. Assign the widgets to the pages, one page can hold multiple widgets.

Step 8. Configure your reports
Configure your reports using the page reports.

Step 9. Use VPVision and save!
Now it is time to lean back, relax and monitor your entire system. Let us know how much you did save! We will reward every white paper or savings success story with a nice gift.

തയ്യാറാക്കൽ

Preparation is the key to smooth installation. A lot of things can be prepared before the actual installation or even the purchase of the complete system.

P&ID

ഒരു ഓവർview of the installation will help you to determine where to install the sensors. Inspect all
locations and make sure that all environmental specifications for the sensors are met.

Contact IT department

പൊതുവായ ആക്‌സസ്
VPVision is a web based monitoring system. An Ethernet connection to the VPVision unit is required to view the system from your computer. The IT department can provide you with IP address(es) and physical connection to the factory Ethernet network.

Define your network

• IP addresses must be unique
• Gateway must be defined
• Subnet mask must be defined
• DNS must be defined
• Relay host needs to be defined in order to send mail
• When using existing network structure: Get your address range: Check with client IT dept

General convention on IP numbers
To make it more easy to find a device, we will use the following guidelines to assign IP addresses to devices in the network. In existing networks, this might not be possible due to limitation.

Ethernet address example

The default address for LAN port: See the configuration leaflet, which comes with your VPVision system.

Example network configuration:

• 10.0.0.1 VPVision-M
• 10.0.0.2 Analog inputs, building 1
• 10.0.0.254 ഗേറ്റ്‌വേ

ഇഥർനെറ്റ് വഴി ബന്ധിപ്പിക്കുക

VPVision can communicate with Modbus and analog sensors via Ethernet. In most factories, Ethernet is available throughout the complete plant.

Access remotely

Make sure that your IT department provides VPN access to the network for remote support.

നിങ്ങൾക്ക് കഴിയും view the VPVision system on any computer, tablet or smartphone as long as the VPVision has access to the Internet. External access to the VPVision system is possible with the VPRouter via the VPInstruments cloud environment. Please contact your IT department in an early stage to prevent any delays. See VPN കണക്ഷൻ കൂടുതൽ വിവരങ്ങൾക്ക്.

Create wiring diagram

A wiring diagram will help you to determine what parts to use.
ഇൻപുട്ടുകൾ

Modbus devices needs to be daisy-chained with a maximum of 8 devices in one chain.
Analog sensors need to be wired to the available ports separately. Up to 8 sensors can be connected
to VPVision Mobile.

ആക്സസറികൾ

ഭാഗം	വിവരണം
VPA.5000.000	5-pin M12 MALE connector (connector with screw terminal)
VPA.5000.010	Cable 10m/32.8ft. with 5 pin M12 on one side
VPA.5000.060	Modbus T Splitter
VPA.5000.061	Modbus RS485 bus termination connector
VPA.5000.062	Modbus cable 10 m with 5 pin M12 on both sides
VPA.5000.105	Modbus cable 5 m with 5 pin M12 on both sides
VPA.5000.063	Modbus cable 1 m with 5 pin M12 on both sides
VPA.5000.160	RS485 network cable set; combination of VPA.5000.060, VPA.5000.062,VPA.5000.063

സെൻസർ കോൺഫിഗറേഷൻ

The sensors require configuration before they can be connected to VPVision. Read the sensor’s manual for more information.

Modbus devices.
A Modbus device needs to have a unique hardware address in it’s daisy chain. Every Modbus sensor in the same daisy chain requires this unique Modbus address. But every Modbus sensor in the same daisy chain also requires equal communication settings like baud rate, parity and stop bits for this daisy chain.

Analog devices
Analog sensor values will need to be converted in to real measurement values. This is done by zero and span where zero matches 4mA and span matches 20mA. These numbers can be calculated during the preparation and will be entered in to VPVision during configuration.

ഹാർഡ്‌വെയർ ഇൻസ്റ്റാളേഷൻ

മുന്നറിയിപ്പ്: Installation involves connection to mains. Installation of field cables requires indepth knowledge and skills. Therefore all steps that involve electrical installation should be carried out by certified installation professionals.

Make sure that the ambient temperature does not exceed the limits of the VPVision(max 40 deg C | 104 F). Higher ambient temperature requires suitcase cooling.

Check if the earth wire (field ground) is free of interference and potential dangerous high voltage. Make sure the circuit breaker is in off position. Then install the L, N and Earth wire. The L, N and Earth may have a different color, depending on your local legislation and directives for medium voltagഇ സംവിധാനങ്ങൾ.

VPVision-M

The VPVision is mounted in a PVC explorer case including:

• AC IN: Two Phase Mains input 100..240 VAC.
• LAN: An Ethernet port for connection to your network. Address can be pre-configured.
• The VPVision-M computer.
• 8 Ch analog input converter
• VPRouter

കുറിപ്പ്: Be aware that VPVision-M must be able to communicate with all the connected sensors and nothing is blocking this communication (firewalls, switches).

പിസി കണക്ഷൻ

You need to set your computer’s IP address to a static ip address when connecting your computer to the VPVision. The address should be within the same IP range as the VPVision. See the configuration sheet which comes with your VPVision to find the default configuration.

To connect your PC or Laptop, use the ethernet port.
Connect an Ethernet cable between laptop (PC) and the VPVision-M LAN. The Laptop should have a static IP address within the same range as the VPVision-M. If you don’t know how to set a statis IP adress on your laptop, please contact your IT department. Make sure the IP address is not the same as the VPVision-M.

നിങ്ങളുടെ തുറക്കുക webbrowser, type in the IP address of the VPVision-M and you should see the startup screen. Now you can configure the system (see Configuration backend).

RS485 കണക്ഷൻ

Installing a RS485 network require specific knowledge. Not following the specifications strictly might result in in-correct communications and equipment damage. Please leave installation up to professional contractors. Make sure that they read this chapter carefully and follow up all RS485 guidelines.

RS485 connection terminal
The VPVision M features 1 pre-wired RS485 interface. It contains the following pins:

പിൻ	സിഗ്നൽ	വയർ നിറം
1	Power + (24VDC)	ബ്രൗൺ
2	Power –	വെള്ള
3
4	Modbus B/+	കറുപ്പ്
5	ModbusA/-	ചാരനിറം

Wire colors apply to VPInstruments cables

RS485 വയറിംഗ്
RS485 is a differential balanced line over twisted pair. It can span relatively large distances up to 1200 meter | 4000 feet. The wires should be connected as a point-to-point configuration, or also called daisy chain. Do not install as star or ring network! The trunk line goes from the master to all devices making a drop down to each device. The cable length from the trunk line to the Modbus device needs to be as small as possible. Junction boxes are used to make the T junction.

Shielded twisted pair should be used. For Modbus field cabling only use the recommended cables. sized and shielded in line with the specific situation in your plant. Connection of a third wire between the master and slave should be done to limit the common mode voltage that can be impressed on the slaves inputs.

ബസ് ശക്തി
The VPFlowScope probe can be powered via the same trunk line. 2 separate wires are used for power + and power. Take in account that long wires with multiple slaves will cause voltage drops. The minimum supply voltage is 12VDC measured at the last VPFlowScope probe in the daisy chain.

ടെർമിനേഷൻ റെസിസ്റ്റർ
Termination resistors reduce electrical noise sensitivity. They need to be added to the installation when cable distances become longer then 10 meter. The value of each termination resistor should be equal to the cable characteristic impedance (typically, 120 ohms for twisted pairs).

There can only be one termination resistor at the very end of the trunk line. The VPInstruments junction box features a jumper that can be used to enable a 120 Ohm resistor. When using the VPinstruments Modbus Junction boxes make sure that the 120 Ohm resistor is only enabled in the last Modbus Junction box in the daisy chain.

പക്ഷപാതം
When there is no data activity on an RS485 network, the communications lines are “floating” and, thus susceptible to external noise or interference. Receivers on a RS485 network have built in hysteresis (200mV differential required to insure known state). To insure that a receiver stays in an inactive state, when no data signal is present, bias resistors are required. Bias resistors are a pull-up resistor on Modbus B and a pull-down resistor on the Modbus A line. The value of the bias resistor depends on the number of devices and the supply voltage. The table below shows which resistor values can be used for different voltage in a chain with 1 to 8 VPFlowScope probes.

വിതരണം വാല്യംtage	പക്ഷപാതം വലിക്കുക up	പക്ഷപാതം വലിക്കുക താഴേക്ക്
12 വി	5 കെ	1 കെ
24 വി	10 കെ	1 കെ

Analog input connection

Analog sensors can be connected to VPVision Mobile. We have chosen for 4..20 mA as default interface. If needed, you can change the I/O converter to 0..10 Volt.

പിൻ	സിഗ്നൽ	വയർ നിറം
1	Power + (24VDC)	ബ്രൗൺ
2	Power –	വെള്ള
3	4-20 mA input	നീല
4
5

Wire colors apply to VPInstruments cables

I/O converter description
This converter contains 8 inputs. Internally, you can find dip switches which affect the analog input configuration. It can be set to 4..20 mA (default) or 0…10 Volt.

4..20 എം.എ
ഒരു അഡ്വാൻtage of a current loop is that the accuracy of the signal is not affected by voltage drop over the line. Even if there is significant electrical resistance in the line, the current loop VPVision Mobile will maintain the proper current, up to its maximum voltage capability. The live-zero represented by 4mA allows the receiving instrument to detect some failures of the loop. An analog current loop can be converted to a voltage input with an external third party precision resistor.

കേബിളിംഗ്
3 wires are required to create a current loop. It is advised to use a shielded cable to prevent electrical noise to affect the signal.

VPRouter (VPN connection)

For safe remote access to the VPVision-M without interfering with the client’s network, a VPRouter is available. In this way it is always possible to access the VPVision-M from a distance and it enables remote support and updates. The VPVision does not send out or retrieve any data to the internet. As long as port 80 is blocked, the VPVision is not visible from outside the premises. For remote viewing. port 80 or another (mapped) port can be added to access the web server from remote.

A cellular internet connection via the VPRouter can be used if it is not possible to create a wired connection.

കുറിപ്പ്: Preferably use the VPN connection in the VPRouter cloud environment for the best connection to your VPVision system.

പവർ സപ്ലൈസ്

The base unit features a UPS 4 Amp (100 Watt) power supply, which delivers power to the VPVision-M, up to 8 Modubs devices and 8 analog 4..20 mA loop powered sensors.

Getting started with VPVision

ടെർമിനോളജി

പേജുകൾ	Pages contain a collection of വിജറ്റുകൾ , they function as dashboard pages.
വിഡ്ജറ്റുകൾ	Widgets represent the data recorded from your ഇൻപുട്ട് ഉപകരണങ്ങൾ.
ഇൻപുട്ട് ഉപകരണങ്ങൾ	Input devices are the physical devices connected to your system.
റിപ്പോർട്ടുകൾ	Reports are generated from Pages as a PDF file and can be configured to be periodically generated and sent through mail.
അലാറങ്ങൾ	Alarms are configured to monitor the state of an input device. Alarms can be configured to trigger a notification when a certain threshold has been reached.

Accessing the site settings

By pressing ‘Manage system’ or ‘Sign-in, you can access the VPVision backend. On smaller screens the sidebar might be hidden, you will need to click the menu button in the top bar to open the sidebar in this case.

Once authenticated you can access various sections used to manage your system. These sections will be listed in the main menu.

In order to return to your VPVision frontend simply press ‘Back to system’ at the top of the menu.

പ്രാമാണീകരണം

The VPVision backend requires user authentication. By default the system is provisioned with an administrator user. You can use this user to start configuring your system.

The credentials for the administrator user are:
ഉപയോക്തൃനാമം: അഡ്മിൻ
പാസ്‌വേഡ്: visionair

It is STRONGLY recommended to change the default password for the administrator user after first authentication.
You can quickly access the current user settings by pressing the user icon in the top bar, and navigating to the “Personal settings” page. The user icon will only be shown when you are signed in.

ഉപയോക്തൃ മാനേജ്മെൻ്റ്

VPVision has support for multiple users accounts. There are 2 user roles available, the default ‘user” and ‘admin’ role.

• Users with the ‘user’ role have limited access to the application and can only manage input devices, pages and other related resources.
• Administrators have access to additional system settings, network management and user management.

You can access the user management by navigating to the ‘User’ section within the VPVision backend.

ഉപകരണങ്ങൾ കൈകാര്യം ചെയ്യുന്നു

Devices are critical for recording data and completely configuring your system. They represent the physical devices attached to your system.
Devices can be added in the ‘Devices’ section within the VPVision backend. They need to be enabled to start recording data.

വെർച്വൽ ഇൻപുട്ടുകൾ

In addition to various physical device types, VPVision also includes a virtual input. The virtual input can be used to combine multiple devices into one output or completely transform the incoming data by applying a formula.
Once a virtual input has been added you will be tasked to configure a formula before enabling the device.
This is done by pressing the ‘Update formula’ button on the device details screen.

For more information about composing formulas please refer to The Formula Editor section in the appendix.

Managing widgets

Widgets represent the data recorded from one or multiple input devices. Additionally VPVision ships with various widgets, like the P&ID widget, used to visualize your environment and can help you in navigating between pages within VPVision.
Widgets can be added in the ‘Widgets’ section within the VPVision backend.

Custom formulas for KPI widgets
Out of the box the KPI widget comes with various predefined calculations. These calculations represent a formula.
VPVision enables you to use your own custom formula within the KPI widget. Custom formula KPIs can be added by selecting the ‘Custom formula’ calculation whilst configuring a KPI widget. Once a KPI has been added with the ‘Custom formula calculation you will be tasked to configure a formula. This is done by clicking the “Update Formula’ button on the widget details screen. This button is only shown for widgets with a custom formula. For more information about composing formulas please refer to The Formula Editor’ section in the appendix.

Managing KPI Calculation types
It is possible the ‘Custom Formula’ or other KPI calculation types are not yet enabled on your system.

To enable various KPI calculation types simply navigate to the ‘KPI Types’ section within the VPVision backend.

Manging pages

Pages are your primary source of data visualization. Pages can contain one or multiple widgets, of any kind, and can be subdivided into multiple windows. Windows are essentially a category within the page
Pages can be added in the ‘Pages section within the VPVision backend.
After adding a page and enabling it, either from the Pages” section or directly whilst adding a new page, the page will be shown in the main menu.

Managing Reports and Alarms

Reports are available for each page, with an option at the top of every page to configure its reports.

Alarms can be configured independently from the rest of the system and are not required to start recording data. An active device is required to configure the alarm
Alarms can be added in the ‘Alarms’ section respectively within the VPVision backend.

For scheduled reporting and automated alarm notifications you need to configure an SMTP outgoing email server
Without an SMTP server reports can be manually downloaded from the Reports page found in the main menu.
Active alarms will be shown in the alarm type widget, this widget needs to be added to your system before you can add it to a page.

VPinstruments Cloud environment

With the VPRouter connection it is possible to remotely access the VPVision-M software via
cloud,voinstruments.com

After signing in with your personal credentials you choose Connect for establishing the VPN connection.
In case there is no VPN available on your local machine, first install the VPN client Browse to 10.0.0.1 in a new tab and you will access the VPVision-M softwar

വിപുലമായ കോൺഫിഗറേഷനുകൾ

As an administrator you can configure various global settings including various regional and reporting settings.
These settings can be bound in the Settings’ section within the VPVision backend.

സിസ്റ്റം

The system settings can be used to rename the system, use an on-screen keyboard, enable data retention, delete data, or perform a factory reset

Language & Region

These settings can be easily customized to align with preferences, including timezone, date/time format, decimal separator, thousand separator, and currency.

റിപ്പോർട്ട് ചെയ്യുന്നു

Reporting settings allow for the customization of display and calculation preferences for widgets and page reports, including options for formatting, start of the week, number rounding, paper size, and the reparting header.

Electricity cost in Euro per kWh, can also be adjusted. Operating hours are applied to constrained KPI calculations.

ഉപയോക്താക്കൾ

It is possible to add more users accounts.

There are 2 user roles available, the default ‘user and admin role.

• Users with the ‘user’ role have limited access to the application and can only manage input devices. pages and other related resources.
• Administrators have access to additional system settings, network management and user management.

നെറ്റ്വർക്ക്

The Network section is available on the Settings section within the VPVision backend. It provides an overview of all active network interfaces.
You may alter the network settings of these interfaces when your site requires it. By default LAN 2 is configured to be used with the VProuter and is used to apply system updates. We do not recommend changing this interface.
If your site does not use the VPRouter, or you need an additional network interface, the settings for this interface can be changed.

മെയിൽ സെർവർ

The Mail Server section within the VPVision backend contains the configuration options for an outgoing SMTP email server.
The SMTP server is disabled by default, if you want to receive scheduled reports or automated alarm notifications it needs to be enabled. Enabling the SMTP server requires an active SMTP capable email server or service.

Configuring Gmail as an outgoing SMTP server

Gmail can be used as an outgoing SMTP server for VPVision. This either requires a personal Google account or a Google Workspace account.

When you use Two Factor Authentication with your Google account you will need to generate an Application password within your Google account before you can authenticate with the outgoing SMTP server.
Depending on your Google Workspace policies you might be required to change additional Google Workspace settings before you can use your Google Workspace account for outgoing SMTP traffic.

ഹോസ്റ്റിൻ്റെ പേര്	smtp.gmail.com
തുറമുഖം	587
എൻക്രിപ്ഷൻ	ടി.എൽ.എസ്
Enable Authentication	അതെ
ഉപയോക്തൃനാമം	Your Google accounts email address
രഹസ്യവാക്ക്	Your Google accounts password or the Application password for VPVision
Sender E-mail Address	Anything you would like as the from address, default no- reply@vpvision.local
Sender Name	Anything you would like as the from name, default VPVision

ഓഡിറ്റ് മോഡ്

Audit Mode operates alongside VPVision’s standard functions, providing real-time data recorded at 1 second intervals, which can be exported to CSV.

Data retention is reviewed every Monday, and any data exceeding the retention period will be automatically deleted. The retention periods are based on UTC.

Please be aware that longer retention periods can result in excessive amounts of raw real-time data VPVision will automatically stop recording when the storage threshold has been reached

CSV Publishing

CSV Publishing works alongside VPVision’s Audit Mode, allowing the data acquisition system to continuously write real-time data at 1-second intervals for all included devices to CSV files. By default, this setting is disabled and must be enabled to start exporting second data. Devices and specific channels can be selected for inclusion by toggling them on or off Configuration options include the decimal separator, value separator, and line separator.

SQL connection

With the SQL Connection you can create read-only users to access the recorded data on your system using the SQL protocol. Once a SQL user is added VPVision will expose a PostgreSQL connection on port 5432 by default.
This section within the VPVision backend contains an oveniew of all available database tables and the SQL Connection user management.
You will need a PostgreSQL. compatible connector to connect with the SQL Connection

ലൈസൻസ്

Your system comes pre-installed with your VP Vision license, if you receive a new license you need to upload the new license through the license page.
The license page can be found in the ‘Settings’ section within the VPVision backend.
On the license page you will find all license details of your currently active license including your device’s serial number, hardware revision and available channels..

സ്പെസിഫിക്കേഷൻ

സ്പെസിഫിക്കേഷനുകൾക്കായി എപ്പോഴും നിങ്ങളുടെ ഉൽപ്പന്നത്തിൻ്റെ ലേബൽ പരിശോധിക്കുക.
Specifications are subject to change as we are continuously improving our products. Please contact us to obtain the latest specification sheet.

മെക്കാനിക്കൽ

കേസ് :PVC Explorer Case
വലിപ്പം:48 x 42 x 22 സെ.മീ | 19 x 16.5 x 8.6 ഇഞ്ച്
ഭാരം:7 കിലോ | 15.4 പൗണ്ട്
Ambient temperature max :40 deg C 104 F
Ambient temperature min :-10 deg C 32 F

ഇലക്ട്രിക്കൽ

പവർ ഇൻപുട്ട് :110-250 VAC
Component perwer :24 വി.ഡി.സി
ഫ്യൂസുകൾ:3.15 A for analog inputs, 3.15 A for Modbus sensors

ഇലക്ട്രോണിക്സ്

കമ്പ്യൂട്ടർ: Industrial faniess mini PC
സംഭരണം: 256 GB Solid State Drive
COM ports: 1x RS485
ഇഥർനെറ്റ് പോർട്ടുകൾ: 1x RJ45

ഇൻപുട്ടുകളും ഔട്ട്പുട്ടുകളും

Modbus terminal : 1x (upto 8 Modbus sensors)
അനലോഗ് ഇൻപുട്ടുകൾ: 8x
Analog inputs modes: 0..10V 4.,20mA

ഡാറ്റ സംഭരണം

Database : SQL
Data retrieval frequency: 1 സെക്കൻഡ്
Data storage intereial:Standard Mode: 1 minute Audit Mode

അനുബന്ധം

Cables for VPVision

All electrical installations to be carried out by authorized electrical installation engineers only.

ഇഥർനെറ്റ്
For Ethernet, Cat5e cable with 4 twisted pairs must be used. For some applications, a higher quality cable might be needed. In case of any doubt, it is best to consult the site on their existing cables to make sure that the VPVision cables match the prescribed standards. The cable should match the power budget of all connected sensors. Long cables will result in increased cable resistance, which might cause issues when not properly addressed.

RS485 മോഡ്ബസ്
For RS485 networks, cable with 2 shielded twisted pairs must be used. One pair will be used to power the connected sensors. The other pair will be used for Modbus data transfer. The quality of this cable depends on the length of the total Modbus chain and the number of sensor attached. Your local contractor can help you calculate the coper wire thickness. Make sure the shield is connected to the power supply side only.

Analog sensors
For 4..20 mA based sensors, a single or double twisted pair cable can be used. The same cable as for Modbus can be used to connect these sensors.

The Formula Editor
The formula editor enables you to compose custom formulas for virtual input devices and KPI widgets based on the custom formula calculation.
Please refer to 6.5 and 6.6 respectively on how to create these instances

Formula Elements
Formulas are composed using formula elements. These are grouped into 3 categories: Inputs, Operators and Endpoints.

• Inputs refer to sensors or a group of sensors, also relerred to as input devices.
• Operators are actions that should be performed on input elements.
• Endpoints indicate the end result of the formula.

ബന്ധിപ്പിക്കുന്ന ഘടകങ്ങൾ

Once a formula element has been added to the editor a dot will be shown next to it. For operators this will be one or two dots to the left and one to the right of the element, endpoints will have a single dot to the left and inputs will have a single dot to the right
These dots represent the input, to the left, and output to the right. To connect an element’s output to the input of the next element simply click and drag the output dot and drag the resulting arrow to the input dot of the next element. Once an element has successfully bean connected the arrow will remain between these elements. Click the arrow to remove this connection.

Grouped Sensors

Grouped sensors are only available to custom formula KPI widgets and consist of all input devices added to the KPI widget during creation. Input devices for custom formula KPI widgets are optional, once they’re added the ‘Summarized’ and ‘Averaged’ input formula elements will be available in the formula editor.

• Summarized grouped inputs consist of all input devices bom the same measurand type and sum the data of all applicable devices.
• Averaged grouped inputs consist of all input devices from the same measurand type and average the summed data of all applicable devices, le. when 3 devices of the same measurand type are added the sum will be divided by 3.

Sensors, Variables and Cost Input elements

Comparable to grouped sensors the sensor input element represents a single input and allows you to select the desired channel and desired starting unit.
Variable input elements are a fixed variable, for example a multiplier or divider. The cost input element is only available to KPI widgets using the custom formula calculation from the cost KPI type
The cost alement represents the electricity cost configured whilst creating a KPI widget. This element is comparable to the variable element.

ഓപ്പറേറ്റർമാർ
Operators apply a certain action to the input data. Most operators allow up to 2 input streams and result in one output. Operator inputs are not limited to input elements and can be combined with the output of a previous operator.

VPVision ships with 5 operator types:
Σ  Sigma addition operator without the 2 inputs max input limit. You can link as many inputs as you like resulting in a single output.

• + Addition limited to 2 inputs resulting in a single output.
• – Subtraction limited to 2 inputs resulting in a single output.
• x Multiplication limited to 2 inputs resulting in a single output.
• ÷ Division limited to 2 inputs resulting in a single output.

It’s important to note that the order of operations is determined by the order of connected inputs.

അന്തിമ പോയിന്റുകൾ

The endpoint element represents the resulting output of the formula. For virtual inputs this can result in a data conversion when the input data is not using the same unit as the endpoint dictates. This isn’t applicable to KPI widgets where the endpoint simply represents a description of your resulting output.
The endpoint, the unit description for virtual inputs or the description you’ve entered for KPI widgets will be shown in widgets where these instances are used. This is most notable for the KPI widget as the description will be directly displayed within the widget.

ട്രബിൾഷൂട്ടിംഗ്
പ്രശ്നങ്ങളും പരിഹാരങ്ങളും

This section will address common problems and their resolution

ഇഷ്യൂ	ലക്ഷണം	കാരണം	റെസലൂഷൻ
Cannot find VPVision in my network		IP conflict, IP address out of range	Re-connect to LAN 1 with a direct Ethernet connection.
VPVision page is not updating	All widgets are static	Connection problems w ith remote IO, network off line, sw itch off line	Restart DAQ process via the configuration backend.
Communication problem	No data on screen	Modbus address or port not properly assigned, Modbus conflict,
	Red LED	Wrong wiring, communication error	Swap RX and TX (A and B) w ire and see if this resolves. Disconnect all but one Modbus device to isolate the problem. Check device settings like baud rate, parity, stop bits
Analog input configuration	VPVision show s 0 as measurement value	The analog module has been reset or the configuration is lost	Log in to the analog module internal w eb server, enable user defined Modbus addresses and set all read out parameters to be located in the holding registers
Wrong kW measurement	Wrong kW in display	The VPLog-i is just an Ampere meter… make sure that the voltage and pow er factor is as correct as possible	If not good enough–> invest in a real kW meter with Modbus

ആശയവിനിമയ പ്രശ്നങ്ങൾ

RS485 Modbus or Analog related issues

• Green: VPVision Data Acquisition is active.
• Red: Communication Error
  

Ethernet issues
Ethernet issues can be localized by pinging the individual components of the system. Each Ethernet device has a unique IP address. The addresses can be pinged and when they respond, you know that the device is reachable. An unreachable device will result in a request time out.

ഡോക്യുമെൻ്റേഷൻ ഉദാample

Proper documentation is key to long term success. Therefore we added an example (empty)
documentation sheet here. You can use it as a guideline for documentation of your VPVision
കോൺഫിഗറേഷൻ.

IP വിലാസ ലിസ്റ്റ്

ഇല്ല	പേര്	IP വിലാസം
1	VPVision-M	10.0.0.1
2	Analog converter	10.0.0.2
3
4
5

ഉപകരണ ലിസ്റ്റ്
Use the list below to write down your configuration. Store this list for future reference

ഇല്ല	പേര്	മോഡ്ബസ് വിലാസം	സ തുറമുഖം	അഭിപ്രായം
1	Packaging dept.	9	3	Pipe diameter = 80.2 mm
2
3
4
5
6
7
8

Analog Channel configuration – Remote analog IO module
Use the list below to write down your configuration. Store this list for future reference

ഇല്ല	പേര്	മിനി (4mA)	പരമാവധി (20mA)	ഇൻപുട്ട് നമ്പർ	കൺവെർട്ടർ IP വിലാസം
1	ഡ്യൂപോയിന്റ്	-40	+10	1	192.168.1.250
2
3
4
5
6
7
8

കുറിപ്പുകൾ

ഇതിനായി തിരയുക your product to get the latest version.
Important updates may be included!

VPVision Mobile

2025 Van Putten Instruments BV

All rights reserved. No parts of this document may be reproduced in any form or by any means – graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval. systems without the written permission of the publisher.

Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the author make no daim to these trademarks.

ഈ പ്രമാണം തയ്യാറാക്കുന്നതിൽ എല്ലാ മുൻകരുതലുകളും എടുത്തിട്ടുണ്ടെങ്കിലും, പിശകുകൾക്കോ ​​ഒഴിവാക്കലുകൾക്കോ ​​അല്ലെങ്കിൽ ഈ ഡോക്യുമെന്റിൽ അടങ്ങിയിരിക്കുന്ന വിവരങ്ങളുടെ ഉപയോഗത്തിൽ നിന്നോ പ്രോഗ്രാമുകളുടെയും സോഴ്‌സ് കോഡിന്റെയും ഉപയോഗം മൂലമുണ്ടാകുന്ന നാശനഷ്ടങ്ങൾക്ക് പ്രസാധകനും രചയിതാവും ഒരു ഉത്തരവാദിത്തവും വഹിക്കുന്നില്ല. അതിനെ അനുഗമിക്കുക. ഈ പ്രമാണം മുഖേന നേരിട്ടോ അല്ലാതെയോ ഉണ്ടായിട്ടുള്ളതോ ആരോപിക്കപ്പെടുന്നതോ ആയ ലാഭനഷ്ടത്തിനോ മറ്റേതെങ്കിലും വാണിജ്യ നാശത്തിനോ ഒരു കാരണവശാലും പ്രസാധകനും രചയിതാവും ബാധ്യസ്ഥരല്ല.

അവസാന പുനരവലോകന തീയതി: 04-04-2025 ഡെൽഫിൽ

പ്രസാധകൻ

വാൻ പുട്ടൻ ഇൻസ്ട്രുമെൻ്റ്സ് ബി.വി
Marlotlaan 1G
2614 GV Delft
നെതർലാൻഡ്സ്

പ്രമാണങ്ങൾ / വിഭവങ്ങൾ

VPInstruments VM-EN-2500 Energy Monitoring System [pdf] ഉപയോക്തൃ മാനുവൽ VM-EN-2500 Energy Monitoring System, VM-EN-2500, Energy Monitoring System, Monitoring System

റഫറൻസുകൾ

• ഉപയോക്തൃ മാനുവൽ